Abbott Optium Xceed
Abbott · Model Optium Xceed
Compact, lightweight and ergonomically designed. Large, clear display with backlight. Test on areas other than your fingertip. Small blood sample. Blood glucose testing. Memory holds 450 test results, displayed averages 7, 14, 30 days. Very fast test time (5 seconds). Upload results to your PC with [i]Precision Link Direct[/i], sold separately. Lifetime Warranty with free once a year battery replacement. Uses Optium Blood Glucose Electrodes. Blood ß-Ketone monitoring. Control solution marking and testing. Backlight: If ON – Stays ON during countdown; turns OFF 30 seconds after result is displayed. If OFF – Stays OFF during countdown; stays OFF during data upload. Beeper: If ON – Beeps when calibrator is fully inserted and when countdown starts and finishes.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Inaccurate or questionable results
HighSymptoms: Result does not fit the clinical picture, poor agreement between duplicate strips, control solution out of range.
Root cause: Damaged, expired or wrong-lot test strips, wrong calibration code, sample too small, or use outside the operating temperature range; haematocrit or interferents.
Meter error / strip problem message
MediumSymptoms: Generic error message on the display during or after a test.
Root cause: Faulty or mis-inserted strip, or a meter fault - repeat with a new strip.
Temperature out-of-range error
MediumSymptoms: Error stating the system is too hot or too cold.
Root cause: Meter and strips outside the specified operating range.
Will not power on / strip not detected
MediumSymptoms: No display on strip insertion, meter will not start a test.
Root cause: Depleted battery or worn/contaminated strip-port contacts.
Data error (E3)
LowSymptoms: "E3" data error on the display.
Root cause: Internal data fault - remove and reinsert the batteries; if it recurs, return the meter.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Battery
Class Frequent wear itemRel. cost $R&R Easy
Blood glucose and β-ketone test strips
Single-use; observe the vial expiry and lot code.
Class Frequent wear itemRel. cost $R&R Easy
Control solution
Class Frequent wear itemRel. cost $R&R Easy
Strip-port contact assembly
Class Periodic replacementRel. cost $$R&R Moderate
Lancing device
Class Periodic replacementRel. cost $R&R Easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Battery | Frequent wear item | $ | Easy |
| Blood glucose and β-ketone test strips Single-use; observe the vial expiry and lot code. | Frequent wear item | $ | Easy |
| Control solution | Frequent wear item | $ | Easy |
| Strip-port contact assembly | Periodic replacement | $$ | Moderate |
| Lancing device | Periodic replacement | $ | Easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Result looks wrong
- Repeat with a new strip and an adequate sample.
- Run the control solution and compare to the range on the vial/insert.
- Confirm the meter code matches the strip lot where the system uses codes.
- Check the ambient temperature is within range.
- If controls are out of range, quarantine the strip lot; if controls pass but patient results still look wrong, refer the meter.
Symptom: Error message on the display
- Turn the meter off and repeat the test with a new strip.
- Move the meter and strips to a location within the operating temperature range if a temperature error is shown.
- Inspect the strip port for dirt, blood or moisture.
- Perform a reader/meter self-test if the model supports it.
- If the error recurs, contact customer service.
Technical Specs
- Height
- 7.47 cm
- Length
- 1.63 cm
- Weight
- 42 g
- Width
- 4.32 - 5.33 cm
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio