Woodway Split-Belt
Woodway · Model Split-Belt
Treadmill The Split-Belt is a locomotion therapy tool that provides infinitely variable speed control of each leg independently, which can accommodate patients with asymmetric walking patterns. The Split-Belt comes standard with PPS style stationary parallel handrails, but can be outfitted with a front-mount single bar for video gait analysis. The SPLIT-BELT comes standard with adjustable handrails like the Bari-Mill. The fully adjustable medical grade handrails have infinite possibilities in width and height, providing a comfort level that is unmatched by stationary parallel bars. The handrails are also beneficial for pediatric use, as the adjustable handrail height accommodates children of all sizes. The SPLIT-BELT can also be outfitted with a front-mount single bar to provide more room for therapist to take a more hands-on approach with the patients.
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Will not start / no display
HighSymptoms: Belt / ramp will not run, no display, no communication with the ECG / stress system.
Root cause: Facility circuit / breaker, a blown fuse, a cut power cord, the control cable to the stress system, or a drive-controller fault.
Speed or grade / incline error
MediumSymptoms: Belt speed or incline does not match the setting, error code, grade drifts.
Root cause: Slat-belt drive or the incline actuator / potentiometer.
Slat / bearing wear
MediumSymptoms: Rough or noisy running, a damaged slat, belt tracking off.
Root cause: Worn transportation-belt bearings or a cracked slat.
Noise / vibration
LowSymptoms: Rumble, squeal or vibration under load.
Root cause: Worn rollers / bearings, drive belt, or motor.
Heart-rate / console readout fault
LowSymptoms: Contact or wireless HR not reading, display segments out.
Root cause: HR receiver / grips or the console board.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Slat set
Class Periodic replacementRel. cost $$$R&R Difficult
Transportation-belt bearings
Class Periodic replacementRel. cost $$R&R Moderate
Drive belt
Class Periodic replacementRel. cost $$R&R Moderate
Incline actuator / potentiometer
Class Major service partRel. cost $$R&R Moderate
Drive motor / controller
Class Major service partRel. cost $$$R&R Difficult
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Slat set | Periodic replacement | $$$ | Difficult |
| Transportation-belt bearings | Periodic replacement | $$ | Moderate |
| Drive belt | Periodic replacement | $$ | Moderate |
| Incline actuator / potentiometer | Major service part | $$ | Moderate |
| Drive motor / controller | Major service part | $$$ | Difficult |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Will not start / no display
- Warning: high voltage can persist under the hood after unplugging - de-energise and unplug before removing covers.
- Confirm the outlet, breaker and power switch.
- Inspect the power cord.
- Check the control cable between the treadmill and the ECG / stress system.
- If power is present and cabling is good, suspect the drive controller.
Symptom: Speed or grade inaccurate
- Verify belt / slat speed with a tachometer against the setting.
- Check the incline actuator and potentiometer range.
- Inspect the drive speed-feedback path.
- Re-verify speed and grade after adjustment.
- Confirm slat tracking and bearing condition.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio