CYBEX 750T
CYBEX · Model 750T
Exercise Programs: 9 Custom, Quick Start, Manual, Hill Interval, Pike's Peak, Heart Rate Control, Weight Loss and Cardio The 750T comes with a 10 x 15 matrix display of workout profile, a 16 character message bar and LED readouts of speed, incline, time, distance, calories, calories/ hr, METs, Pace and Heart rate. Display: 10" x 15" Matrix LED Display Readouts: Time, speed, and incline Heart Rate Monitoring: Contact or wireless Safety Sentry: Knows whether you are there or not and will stop the belt after the pre-selected waiting period helping to keep members safe Speed Range: 0.5 - 15.6 mph (0.8 - 39.5 km/h) Elevation Range: -3% - 15% Running Area (L x W): 62" x 22" / (157 x 56 cm) Step Up Height: 11.5" (29 cm) Motor: 6 HP Peak AC Cushioning system: Intelligent Suspension System from CYBEX Optional Audio Visual Key Pad- included Personal Entertainment Monitor- optional TV: Optional iPod/ iPhone Compatibility- with Personal Entertainment Monitor 11 Available Languages- included Cooling Fan- included Handrails: ARMZ stability bars Convenience Features: 2 Large Water Bottle Holders, Magazine Rack, Utility Tray Electrical receptacle & plug: NEMA 5-20R 120v Electrical requirements: 20 amps, dedicated circuit required, non-looped grounded.
Key tips
- ·A no-signal/flatline alarm gets checked on the patient first, not the monitor - rule out a real clinical event before troubleshooting.
- ·Recalibrate NIBP against a reference manometer, not just a self-test pass.
- ·Reused patient cables (SpO2, ECG leads) are a common source of intermittent-fault complaints - swap the cable before the module.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Belt slips, drifts or runs rough
HighSymptoms: Walking belt slips under load, tracks off-centre, jerky or noisy.
Root cause: Worn or stretched belt, a worn deck, loss of drive-belt tension, or worn rollers.
Will not start / no speed or incline response
HighSymptoms: Console dead, belt will not move, incline will not change, error code.
Root cause: Breaker / power, a drive-motor or controller fault, a lift-motor fault, or a console-cable fault.
Speed or incline inaccuracy
MediumSymptoms: Actual speed / grade does not match the display or protocol.
Root cause: Speed-sensor or incline-potentiometer / limit-switch fault - needs calibration.
Drive-motor / controller fault
MediumSymptoms: Motor cuts out under load, burning smell, controller error.
Root cause: Worn motor brushes / bearings or a drive-controller fault.
Emergency-stop / safety-key fault
HighSymptoms: E-stop or safety key does not stop the belt, or stops it unexpectedly.
Root cause: Failed e-stop switch / magnet or its wiring - a safety function.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Walking belt & deck
Class Periodic replacementRel. cost $$R&R Moderate
Drive belt
Class Periodic replacementRel. cost $R&R Moderate
Drive motor / controller
Class Major service partRel. cost $$$R&R Difficult
Incline (lift) motor / potentiometer
Class Major service partRel. cost $$R&R Moderate
Roller / bearing set
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Walking belt & deck | Periodic replacement | $$ | Moderate |
| Drive belt | Periodic replacement | $ | Moderate |
| Drive motor / controller | Major service part | $$$ | Difficult |
| Incline (lift) motor / potentiometer | Major service part | $$ | Moderate |
| Roller / bearing set | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Routine cable and lead-wire inspection for fraying/wear
- ·Battery conditioning cycle
- ·NIBP calibration check against a reference manometer
- ·ECG / SpO2 accuracy verification against a patient simulator
- ·Annual electrical safety test
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Belt slips or tracks off
- Check and set the walking-belt tension and tracking per the manual.
- Inspect the deck and belt for wear (a worn deck kills belts).
- Check the drive-belt tension.
- Lubricate the deck if the design requires it.
- Replace the belt / deck as a set when worn.
Symptom: Will not start or speed/incline wrong
- Confirm mains, the breaker and the safety key.
- Read any console error code.
- Check the console cable and the drive / lift-motor connections.
- Verify belt speed with a tachometer and calibrate speed / incline.
- Replace the drive controller, motor or incline potentiometer as isolated; confirm the e-stop stops the belt.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- ICU / CCU
- Emergency Department
- OR / PACU
- General med-surg floors
- Step-down units
- Telemetry units
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio