Stryker Cast Cutter
Stryker · Model Cast Cutter
Dual speed cutting to meet varied cast removal needs. Compact design to enhance maneuverability. Three blades to fit multiple casts types. Total compatibility with the 986 Cast Vac. Option of operating independently of the 986 Cast Vac.
Key tips
- ·Never defeat or bypass a return-electrode monitoring (REM) alarm to finish a case - it's a direct burn risk.
- ·Verify OR table battery backup - a table that loses power mid-procedure is a real, documented incident type.
- ·Track surgical light lamp-hours rather than waiting for failure - a sudden failure mid-case is avoidable.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Blade will not oscillate / weak cut
HighSymptoms: Motor runs slow or stalls in the cast, no oscillation, bogs down.
Root cause: Worn motor brushes / armature, a worn eccentric / bearing, or a dull blade.
Excess heat at the blade
MediumSymptoms: Blade gets very hot quickly, burn risk.
Root cause: Dull or wrong blade, a worn bearing, or a seized dust extraction.
Dust-extraction fault (vac units)
MediumSymptoms: Poor suction, dust everywhere, filter full.
Root cause: Full filter / bag, a hose blockage, or a worn vacuum motor.
Excess noise / vibration
LowSymptoms: Loud, buzzy, uncomfortable to hold.
Root cause: Worn bearings or a loose blade nut.
Power cord / switch fault
LowSymptoms: Intermittent or dead on the trigger.
Root cause: Worn cord or trigger switch.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Motor brushes / armature
Class Periodic replacementRel. cost $$R&R Moderate
Eccentric / bearing kit
Class Periodic replacementRel. cost $$R&R Moderate
Blades
Class Frequent wear itemRel. cost $R&R Easy
Vacuum filter / bag (vac units)
Class Frequent wear itemRel. cost $R&R Easy
Trigger switch / cord
Class Periodic replacementRel. cost $R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Motor brushes / armature | Periodic replacement | $$ | Moderate |
| Eccentric / bearing kit | Periodic replacement | $$ | Moderate |
| Blades | Frequent wear item | $ | Easy |
| Vacuum filter / bag (vac units) | Frequent wear item | $ | Easy |
| Trigger switch / cord | Periodic replacement | $ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Pre-case functional check
- ·Electrosurgical return-electrode cable inspection
- ·Table hydraulic / mechanical inspection
- ·Annual electrical safety test and full PM
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Weak cut or blade stalls
- Fit a fresh, correct blade and confirm it is tight.
- Check the motor brushes and armature.
- Feel the eccentric / bearing for roughness.
- Replace the brushes or bearing kit.
- Confirm free oscillation and cutting on a scrap cast.
Symptom: Blade overheats
- Use a sharp blade and let it cool between cuts.
- Check the bearing is not dragging.
- Clear the dust extraction (vac units).
- Replace the bearing kit if the blade heats with a good blade.
- Confirm normal running temperature.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Operating rooms
- Procedure rooms
- Interventional suites
Documents & Manuals
Safety & Recalls
Synced live from the FDA openFDA API.
- RECALL
Stryker Instruments is voluntarily recalling the single use 2.5MM Aggressive Blade because the line on the affected part (P/N 5290-928-000, Lot #13280CG2) was a straight line without a number scale or logo. The line required for this part number includes a number scale that goes from 1cm 7cm.
- RECALL
Potential breakage of the internal shaft of the End Cutter Shaver Blade; F-Series, 4.0mm. if breakage occurs, the device becomes non-functional and the defect could be observed through the camera/console system.
- RECALL
Disposable Patella Cutters - 30 mm (catalog number 8000-0030, lot V31257001) were packaged and labeled as 33 mm Disposable Patella Cutters (catalog number 8000-0033, lot V31257001 and vice versa.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio