Mindray BeneView T5/T6/T7/T8/T9
Mindray · Model BeneView T5/T6/T7/T8/T9
Provides audible and visual alarm indications in case of patient or equipment problems Enables displaying reviewing, storing and transferring of real-time data Incorporates multiple input devices such as buttons, knobs, touchscreen, keyboard, and mouse Interfaces a clinical information system or central monitoring system Up to 48 hours of Full Disclosure waveforms and numeric data Review up to 120 hours of tubular and graphic trends including OxyCRG Quick-function buttons Screen layout can be changed easily User-configurable quick keys access your most frequently used and essential functions Backup battery CF storage card.
Key tips
- ·A no-signal/flatline alarm gets checked on the patient first, not the monitor - rule out a real clinical event before troubleshooting.
- ·Recalibrate NIBP against a reference manometer, not just a self-test pass.
- ·Reused patient cables (SpO2, ECG leads) are a common source of intermittent-fault complaints - swap the cable before the module.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
A parameter drops out or reads wrong
HighSymptoms: ECG, IBP, SpO2, temperature, CO2 or CO intermittently drops or is implausible.
Root cause: Worn patient cable / sensor, or a parameter-module / input-board fault.
NIBP will not measure or is inaccurate
MediumSymptoms: NIBP times out, cuff will not inflate / hold, readings implausible.
Root cause: Internal NIBP pump or valve, a cuff / hose leak, or a pressure-transducer fault.
Module / parameter board not recognised
MediumSymptoms: Host does not display a module or built-in parameter.
Root cause: Docking / connector or an internal board fault.
Display / touchscreen fault
MediumSymptoms: Blank, dim or distorted display, unresponsive touchscreen.
Root cause: Display, backlight, or controller fault.
Battery / power fault
MediumSymptoms: Short battery run time, will not hold charge, will not power on.
Root cause: Aged battery pack or a power-supply fault.
Network / central-station connectivity fault
LowSymptoms: Monitor not shown at the central station, telemetry drops, admit fails.
Root cause: Wired / Wi-Fi network configuration or a communication board.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Patient cable set (ECG / IBP / SpO2 / temp)
Class Frequent wear itemRel. cost $$R&R Easy
NIBP cuff and hose
Class Frequent wear itemRel. cost $R&R Easy
Internal NIBP pump / valve
Class Major service partRel. cost $$$R&R Difficult
Parameter module / input board
Class Major service partRel. cost $$$R&R Difficult
Battery pack
Class Periodic replacementRel. cost $$R&R Fairly easy
Display / touchscreen assembly
Class Major service partRel. cost $$$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Patient cable set (ECG / IBP / SpO2 / temp) | Frequent wear item | $$ | Easy |
| NIBP cuff and hose | Frequent wear item | $ | Easy |
| Internal NIBP pump / valve | Major service part | $$$ | Difficult |
| Parameter module / input board | Major service part | $$$ | Difficult |
| Battery pack | Periodic replacement | $$ | Fairly easy |
| Display / touchscreen assembly | Major service part | $$$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Routine cable and lead-wire inspection for fraying/wear
- ·Battery conditioning cycle
- ·NIBP calibration check against a reference manometer
- ·ECG / SpO2 accuracy verification against a patient simulator
- ·Annual electrical safety test
Error Codes
Extracted directly from this unit's own service manual.
[CO2 Purging]The alarm message [CO2 Purging] is displayed on the screen after certain time. Block the gas inlet for another 30s.
[CO2 FilterLine Err]it indicates that the module does not leak.
[AG Airway Occluded]An alarm message [AG Airway Occluded] will appear on the screen.
[Calibration Completed!]If the calibration is finished successfully, the message [Calibration Completed!] is displayed in the [Calibrate CO2] menu.
[Calibration Failed!]If the calibration failed, the message [Calibration Failed!] is displayed. In this case, perform another calibration.
[Current FlowRate]In the [Calibrate AG] menu, the concentration of each measured gas and flow rate are displayed.
[SetFlowRate]In the [Calibrate AG] menu, the concentration of each measured gas and flow rate are displayed.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: A parameter drops out
- Reseat the patient cable at the module / monitor.
- Swap in a known-good cable / sensor for that parameter.
- Dock the module on a different host / slot to isolate module vs host.
- Inspect the docking connector for bent pins.
- Replace the cable or refer the module / input board if the fault stays with it.
Symptom: Display or network fault
- Power-cycle the monitor.
- Check the display / backlight and cabling for the display fault.
- For a network fault, confirm the cable / Wi-Fi settings and that other monitors on that drop are online.
- Verify the central-station admit and the monitor's network address.
- Escalate a whole-unit outage to the network / central-station server.
Technical Specs
- Height
- 370
- Length
- 193
- Power Requirements
- 100-240 VAC
- Weight
- 10.5 kg
- Width
- 400
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- ICU / CCU
- Emergency Department
- OR / PACU
- General med-surg floors
- Step-down units
- Telemetry units
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio