Medivance Arctic Sun 5000
Medivance · Model Arctic Sun 5000
Fast initiation of treatment Simple programming capabilities Comprehensive built-in training module Easy access to treatment data Precise Temperature Control: Enhanced treatment algorithm over the Arctic Sun 2000® Temperature Management System Rapid Clinician Training: Intelligent automation and built-in education tutorial Comprehensive Implementation Program: Arctic Circle™ Clinical Resource Program.
Key tips
- ·Never skip temperature-accuracy verification to save time - it's the one check that directly prevents burns.
- ·Hose/blanket connector wear is the most common real fault and the easiest to miss on a quick visual check.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Patient temperature not reaching / holding target
HighSymptoms: Servo control cannot achieve or hold the target core temperature, slow rate of change, water-temperature limit reached.
Root cause: ArcticGel pad contact / coverage, a circuit air lock, low water level, a pump fault, or a heater / chiller (TEC) fault - use the Diagnostic screen (flow, pressure, water-sensor readings).
Low flow / high pressure / air-in-line alarm
MediumSymptoms: Circuit alarm, delivery pauses, flow low on the Diagnostic screen.
Root cause: Kinked or clamped pad lines, a disconnected pad, an air lock, or a pump / manifold fault.
Patient-temperature probe fault
MediumSymptoms: Core / surface temperature reads implausibly, probe-fault alarm, servo unavailable.
Root cause: Damaged temperature probe or its adapter cable.
Water reservoir / leak fault
MediumSymptoms: Low-water alarm, water around the unit, will not fill.
Root cause: Reservoir leak, a fill-port issue, or worn internal tubing / seals.
Calibration drift
MediumSymptoms: Water or patient temperature disagrees with a reference on the calibration check.
Root cause: Temperature-sensor or control calibration.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
ArcticGel pads / hoses
Class ConsumableRel. cost $$R&R Easy
Patient temperature probe / adapter cable
Class Frequent wear itemRel. cost $$R&R Easy
Circulation pump
Class Periodic replacementRel. cost $$$R&R Difficult
Heater / chiller (TEC) module
Class Major service partRel. cost $$$$R&R Difficult
Water reservoir / internal tubing kit
Class Periodic replacementRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| ArcticGel pads / hoses | Consumable | $$ | Easy |
| Patient temperature probe / adapter cable | Frequent wear item | $$ | Easy |
| Circulation pump | Periodic replacement | $$$ | Difficult |
| Heater / chiller (TEC) module | Major service part | $$$$ | Difficult |
| Water reservoir / internal tubing kit | Periodic replacement | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Hose / blanket connector inspection
- ·Temperature-accuracy verification
- ·Annual electrical safety test
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Not reaching / holding target
- Open the Diagnostic screen and review flow, pressure and the individual water-temperature sensors; check the Event Log.
- Confirm adequate pad coverage and good skin contact, and prime out any air.
- Confirm the water reservoir is filled and the pump runs at the expected flow.
- Run a calibration check against a reference.
- Escalate a confirmed heater/chiller or pump fault to Medivance / BD.
Symptom: Flow / pressure / air alarm
- Check the pad lines for kinks, clamps and disconnections.
- Prime the circuit to clear air.
- Confirm the pads are the correct type and fully connected.
- Watch the flow recover on the Diagnostic screen.
- Replace the pad set or refer the pump / manifold if it persists.
Technical Specs
- Height
- 35 in
- Length
- 18.5 in
- Weight
- 43 kg
- Width
- 14 in
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Operating Room
- PACU
- Emergency Department
- Labor & Delivery
- NICU
Documents & Manuals
Safety & Recalls
Synced live from the FDA openFDA API.
- RECALL
If temperature management system fails to reach correct target water temperature while device is operating in patient control mode, due to sudden patient temperature changes/interruption in water flow/blockage of air flow by an obstruction or dirty filter, then system may not alert, and alarm absence may lead to hypothermia or hyperthermia, so a software update will be released to correct issue.
- RECALL
Potential for an inaccuracy of the primary patient temperature reading that is used to monitor and control patient temperature.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio