Lancer 1400 LXP
Lancer · Model 1400 LXP
Larger and wider chamber for greater capacity and volume with three levels of cleaning More robust control system allowing for great washer functionality Optional independent monitoring system Powerful and rapid HEPA filtered drying through injectors and in wash chamber Increased safety with on-board storage and input of chemicals Higher grade 316 L Stainless Steel Chamber Fast cycles and outstanding results from powerful wash action and design Easy to use microprocessor controls with self-diagnostic software and alarms Flexibility of multi-level injection washing and interchangeable racks All sizes and types of glassware cleaned with chamber configuration choices Ergonomic and safe loading of racks on load bearing telescopic runners Choice of preset and user-customized (PIN code protected) programs Accurate and repeated intake of cleaning chemicals by automatic peristaltic dosing pumps Robust high grade 304 L and 316L stainless steel construction (varies by model) IQ/OQ protocol and validation options available Cost effective Low life cycle costs and efficient operation uses less resources and inventory Eco-friendly low energy, chemicals and water usage.
Key tips
- ·A failed biological indicator means the entire load is not sterile - no exceptions, regardless of how the cycle printout looks.
- ·Door gasket wear is the most common real cause of a failed vacuum/pressure test - check it before deeper diagnostics.
- ·Water quality directly affects steam-cycle validity - don't ignore scale or mineral buildup.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Cycle fault / abort
HighSymptoms: Cycle stops with a fault code, load not processed, door locked.
Root cause: Water fill / drain fault, temperature not reached, a dosing-pump fault, or a spray-arm blockage.
Poor cleaning / spray-arm blockage
MediumSymptoms: Instruments come out soiled, spray arms not rotating.
Root cause: Clogged spray-arm nozzles, a blocked filter / strainer, or low water pressure.
Chemistry dosing fault
MediumSymptoms: Detergent / neutraliser / lubricant not dosed, dosing-pump alarm.
Root cause: Empty chemistry container, an air-locked or worn dosing pump, or a level sensor.
Thermal-disinfection temperature not reached
HighSymptoms: A0 / disinfection temperature not achieved.
Root cause: Heater element, temperature sensor, or steam supply.
Door / seal fault
MediumSymptoms: Leaks during the cycle, door will not lock / unlock.
Root cause: Worn door gasket or a door-lock solenoid.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Spray-arm nozzles / bearings
Class Periodic replacementRel. cost $$R&R Fairly easy
Chamber filter / strainer
Class Frequent wear itemRel. cost $R&R Easy
Peristaltic dosing pump / tubing
Class Periodic replacementRel. cost $$R&R Moderate
Heater element / temperature sensor
Class Major service partRel. cost $$R&R Moderate
Door gasket
Class Periodic replacementRel. cost $$R&R Fairly easy
Fill / drain solenoid valve
Class Periodic replacementRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Spray-arm nozzles / bearings | Periodic replacement | $$ | Fairly easy |
| Chamber filter / strainer | Frequent wear item | $ | Easy |
| Peristaltic dosing pump / tubing | Periodic replacement | $$ | Moderate |
| Heater element / temperature sensor | Major service part | $$ | Moderate |
| Door gasket | Periodic replacement | $$ | Fairly easy |
| Fill / drain solenoid valve | Periodic replacement | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily biological and chemical indicator test loads
- ·Door gasket / seal inspection
- ·Steam trap and drain strainer cleaning
- ·Annual full PM and pressure-vessel certification
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Cycle fault / abort
- Note the fault code and the phase it aborted in.
- Check the water fill and drain and clean the chamber filter / strainer.
- Confirm the spray arms rotate freely and the nozzles are clear.
- Verify the heater reaches the disinfection temperature and the sensor agrees with a reference.
- Follow the service manual for the specific code; replace the failed valve / heater / sensor.
Symptom: Instruments come out soiled / spray arms not turning
- Clear the spray-arm nozzles and confirm each arm spins freely.
- Clean the chamber filter / strainer and the drain.
- Confirm detergent and neutraliser are dosing (prime the pumps).
- Check the wash-water pressure and temperature.
- Run a soil / protein-residue test on the next cycle.
Symptom: Chemistry not dosed / dosing-pump alarm
- Confirm the chemistry containers are not empty and the pick-up tubes reach the fluid.
- Prime the dosing pumps and clear any air lock.
- Check the dosing-pump tubing for wear and the level sensors.
- Verify the dosed volume per the service procedure.
- Replace worn peristaltic tubing or the dosing pump.
Symptom: Disinfection temperature (A0) not reached / door-seal leak
- Compare the chamber temperature to an independent reference during the hold.
- Check the heater element draws current and the steam supply (if steam-heated).
- Inspect the door gasket for a leak and the door-lock solenoid.
- Replace the temperature sensor if it disagrees with the reference.
- Re-run and confirm the A0 / hold is met.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Central Sterile Supply Department (CSSD)
- OR sterile core
- Satellite reprocessing areas
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio