Kinetec Centura S1
Kinetec · Model Centura S1
Anatomical Shoulder CPM Machine. The KINETEC CENTURA is composed of 5 complementary and anatomical movements covering most of the shoulder pathologies: Abduction / Adduction - Aduction/Adduction with sychronised rotation Shoulder Rotataion - Shoulder Flexion / Extension - Horizontal Adbuction. Easy left to right arm switch system Patient set-up is anatomical, comfortable and quick with an intuitive colour- coded system Evolution Compliant The KINETEC CENTURA is available in different versions to fit with your daily requirement and use. The device has been designed with additional modules so the user can upgrade the product as required Kinetec Data CaptureTM USB technology ready The KINETEC CENTURA remote control feature the latest USB technology enabling the use of the KINETEC DATA CAPTURE software and patient USBs to track patient progress as well as pre-program the entire patient rehabilitation protocol.
Key tips
- ·Most "no output" stim-unit complaints are cable-side - check electrode/lead continuity before assuming a unit fault.
- ·Frame and strap wear on mechanical rehab equipment is a real fall/injury risk - don't defer it as cosmetic.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Motor / actuator / drive will not run or is weak
HighSymptoms: Traction force not applied, CPM carriage will not move or stalls, drive assist weak, motion one direction only.
Root cause: Worn drive motor / leadscrew / actuator, a hand-control fault, or a control-board fault.
Force / range / position inaccuracy
MediumSymptoms: Set traction force or CPM angle not reached, load cell drifts, carriage overshoots or stalls short.
Root cause: Load-cell / position-sensor drift, a potentiometer fault, or a limit-switch fault.
Hand control / patient-control fault
MediumSymptoms: Hand control unresponsive, the patient stop / reverse button does not work.
Root cause: Worn hand control or a damaged cable.
Frame / bearing / cable wear
MediumSymptoms: Rough or noisy travel, play in the carriage, frayed traction cord or rope.
Root cause: Worn bearings / slides or a frayed cable / cord.
Power / battery fault
LowSymptoms: Will not power on, short battery run time.
Root cause: Power supply / fuse or an aged battery.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Drive motor / leadscrew / actuator
Class Major service partRel. cost $$$R&R Difficult
Load cell / position sensor / potentiometer
Class Major service partRel. cost $$R&R Moderate
Hand control
Class Periodic replacementRel. cost $$R&R Fairly easy
Bearings / slides / traction cord
Class Periodic replacementRel. cost $$R&R Moderate
Power supply / fuse / battery
Class Major service partRel. cost $R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Drive motor / leadscrew / actuator | Major service part | $$$ | Difficult |
| Load cell / position sensor / potentiometer | Major service part | $$ | Moderate |
| Hand control | Periodic replacement | $$ | Fairly easy |
| Bearings / slides / traction cord | Periodic replacement | $$ | Moderate |
| Power supply / fuse / battery | Major service part | $ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Frame and strap wear inspection
- ·Electrode lead continuity check
- ·Annual electrical safety test
Error Codes
Extracted directly from this unit's own service manual.
ANGULAR POSIPotentiometer cable breaking between the copy potentiometer and the PCB card.
Check the electrical continuity of each electrical wire.
NO MOVEMENTThe motor strap is broken. - The motor block is defective.
Change the strap. - Change the motor block.
BAD WAYThe potentiometer electrical wires are inverted.
LOAD MAXIThe motor consumption is over the limits.
Change the motor.
SERV. MOTORThe machine has 2 000 hours service. You have to do a revision.
POWER SUPPLYThe power supply doesn't work correctly.
Change the power supply.
DEFAUT AXE DECONNECTEThe spiral cable is disconnected while the machine is working.
If the problem still remains, the spiral cable is defective. - Check the connections. - Change the spiral cable.
SELECT VALID MOVEMENTThe programmed movement isn't the one connected.
Connect the right movement. - If the problem still remain, change the spiral cable and the PCB card if necessary.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: No or low output on a modality / channel
- Fit a fresh applicator / handpiece / electrodes for that modality.
- Substitute a known-good lead / cable.
- Test therapeutic-ultrasound output into a water bath (visible cavitation / warmth) and run the applicator-contact / BNR self-test.
- Try the modality on another unit if available.
- Escalate a confirmed output-stage fault to the OEM.
Symptom: Patient feels nothing / open-circuit on an e-stim channel
- Fit fresh self-adhesive electrodes on well-prepped skin.
- Swap the lead wires.
- Confirm the current ramps and there is no open-electrode alarm.
- Test the channel into a resistive load per the manual.
- Refer the output stage if a good lead set still gives nothing.
Symptom: Unresponsive or erratic touchscreen / parameters will not set
- Power-cycle the unit.
- Recalibrate / re-seat the touchscreen if the touch is offset.
- Check the mains fuse and power supply.
- Confirm the cooling fan runs and the vents are clear.
- Replace the touchscreen or power supply as isolated.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Physical therapy / rehab gym
- Outpatient rehab clinic
- Sports medicine
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio