HealthySole UVC Germicidal Disinfection
HealthySole · Model UVC Germicidal Disinfection
Introducing groundbreaking use of UVC technology that eliminates the dangerous organisms that cause healthcare-associated infections (HAI's). Add a significant layer of defense to your existing infection control/prevention program. Once implemented, this product will reduce the rate of airborne, horizontal and cross contamination - without labor costs!
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
System does not power on
MediumSymptoms: No power, indicators dark.
Root cause: AC power not present (cord not seated, wall receptacle dead, tripped breaker) or a blown AC fuse in the snap-in holder between the ON/OFF switch and the cord socket.
Shutters will not open
HighSymptoms: System powers on but the UVC shutters stay closed, no exposure.
Root cause: Safety interlock not made (base cover / dust shield not seated after service), the interlock cable unplugged, or an IR foot/heel sensor cable disconnected.
Lamps do not turn on
HighSymptoms: Shutters open but no UVC output, treatment time counts with no disinfection.
Root cause: UVC lamp(s) at end of life, a lamp not seated, or a lamp-driver / ballast fault.
IR foot sensor not detecting
MediumSymptoms: Cycle does not start when a user steps on, or ends early.
Root cause: Toe or heel IR sensor obstructed, dirty, or its cable unplugged from the system board.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
UVC lamps
Handle with gloves; re-seat the safety-interlock cable after replacement.
Class Frequent wear itemRel. cost $$R&R Moderate
AC fuses (snap-in pair)
Class Major service partRel. cost $R&R Fairly easy
IR toe / heel sensors
Class Periodic replacementRel. cost $$R&R Moderate
Dust shield
Class Frequent wear itemRel. cost $R&R Fairly easy
Lamp driver / ballast
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| UVC lamps Handle with gloves; re-seat the safety-interlock cable after replacement. | Frequent wear item | $$ | Moderate |
| AC fuses (snap-in pair) | Major service part | $ | Fairly easy |
| IR toe / heel sensors | Periodic replacement | $$ | Moderate |
| Dust shield | Frequent wear item | $ | Fairly easy |
| Lamp driver / ballast | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Will not power on
- Confirm the power switch is ON and the cord is fully inserted at the base and the wall.
- Test the wall receptacle with another appliance and check the circuit breaker.
- Remove the power cord and check the two AC fuses in the snap-in holder between the switch and the cord socket.
- Replace blown fuses with the same rating.
- If still dead, refer for service.
Symptom: Shutters or lamps will not activate
- Confirm the system is powering on.
- Check the safety interlock: after any dust-shield or lamp change, ensure the base cover is installed correctly and the interlock cable is plugged into the system board.
- Confirm the toe and heel IR sensor cables are connected.
- Reseat the lamps and their driver connections.
- Replace lamps at end of life.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio