Delfi PTS ii
Delfi · Model PTS ii
Two-in-One Solution Independent instruments provide flexibility and cost savings to facilities with multiple OR’s, by allowing twin systems to be separated and used as two single units. For IVRA procedures, simply bring unis back together. Intelligent Touch Intuitive user interface simplifies key tourniquet parameters and user training. Personalized Pressure Limits Limits normal maximum pressure to 475 mmHg, and allows selection of extended pressure of up to 600 mmHg if required for individual patients. Advanced Leak Detection During Surgery Monitors the tourniquet cuff, tubing and connectors for air leaks during surgery, and safely alerts staff to hazards. Speed Reduces set-up and inflates a typical 34" thigh cuff in less than 5 seconds. Integrated Tourniquet Cuff Testing Enables cuff testing before or after surgery as recommended in current AORN Standards and Recommended Practices. Advanced Safety Features Intuitive time and pressure safety alarms; unique self-test and calibration test; visible displays of pressure and time. Greatest Battery Life Up to 10 hours of operation with tested cuffs. Connectivity Allows easy integration with OR information networks.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Will not reach or hold set cuff pressure
HighSymptoms: Pressure droops during a case, will not inflate to setpoint, leak alarm.
Root cause: Internal pump / compressor wear, a solenoid-valve fault, or a leak in the tubing / cuff / connectors.
Pressure inaccuracy / calibration drift
HighSymptoms: Displayed pressure differs from an independent gauge - patient-safety critical.
Root cause: Pressure-transducer drift or a calibration fault.
Dual-channel / bilateral fault
MediumSymptoms: One channel will not regulate independently, cross-talk between channels.
Root cause: Channel solenoid / transducer or a manifold fault.
Alarm / timer fault
MediumSymptoms: Inflation-time alarm not sounding, timer wrong.
Root cause: Alarm / timer board fault - a safety function.
Tubing / connector / cuff fault
MediumSymptoms: Leak at the connector, cuff will not hold.
Root cause: Worn tubing, connectors, or a damaged cuff.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Internal pump / compressor
Class Major service partRel. cost $$$R&R Difficult
Solenoid / regulator valve
Class Major service partRel. cost $$R&R Moderate
Pressure transducer
Verify against a calibrated gauge after replacement.
Class Periodic replacementRel. cost $$R&R Moderate
Connecting tubing / connectors
Class Frequent wear itemRel. cost $R&R Easy
Alarm / control board
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Internal pump / compressor | Major service part | $$$ | Difficult |
| Solenoid / regulator valve | Major service part | $$ | Moderate |
| Pressure transducer Verify against a calibrated gauge after replacement. | Periodic replacement | $$ | Moderate |
| Connecting tubing / connectors | Frequent wear item | $ | Easy |
| Alarm / control board | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Will not hold set pressure
- Fit known-good tubing and a known-good cuff.
- Occlude the outlet and confirm the pump holds pressure.
- Check the solenoid / regulator valve.
- Verify displayed pressure against a calibrated reference gauge across the range.
- Rebuild / replace the pump, valve or transducer as isolated.
Symptom: Pressure reads inaccurately
- Tee in a calibrated gauge and compare at several set pressures.
- Run the calibration procedure per the service manual.
- Confirm both channels on a dual unit.
- Confirm the inflation-time alarm sounds.
- Do not use the tourniquet clinically until pressure accuracy is confirmed.
Technical Specs
- Height
- 7 in
- Length
- 4.3 in
- Weight
- 38 oz
- Width
- 4.7 in
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio