Zimmer ATS 2200
Zimmer · Model ATS 2200
Personalized Pressure™ Technology Limb Occlusion Pressure (L.O.P.) Dual Port Dual Cuff Table or Pole Mount Lithium Ion Battery - 6 hours Touchscreen User Interface Compliant with International Alarm Standard 60601-1-8 8.4" Color Display.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Will not reach or hold set cuff pressure
HighSymptoms: Pressure droops during a case, will not inflate to setpoint, leak alarm.
Root cause: Internal pump / compressor wear, a solenoid-valve fault, or a leak in the tubing / cuff / connectors.
Pressure inaccuracy / calibration drift
HighSymptoms: Displayed pressure differs from an independent gauge - patient-safety critical.
Root cause: Pressure-transducer drift or a calibration fault.
Dual-channel / bilateral fault
MediumSymptoms: One channel will not regulate independently, cross-talk between channels.
Root cause: Channel solenoid / transducer or a manifold fault.
Alarm / timer fault
MediumSymptoms: Inflation-time alarm not sounding, timer wrong.
Root cause: Alarm / timer board fault - a safety function.
Tubing / connector / cuff fault
MediumSymptoms: Leak at the connector, cuff will not hold.
Root cause: Worn tubing, connectors, or a damaged cuff.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Internal pump / compressor
Class Major service partRel. cost $$$R&R Difficult
Solenoid / regulator valve
Class Major service partRel. cost $$R&R Moderate
Pressure transducer
Verify against a calibrated gauge after replacement.
Class Periodic replacementRel. cost $$R&R Moderate
Connecting tubing / connectors
Class Frequent wear itemRel. cost $R&R Easy
Alarm / control board
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Internal pump / compressor | Major service part | $$$ | Difficult |
| Solenoid / regulator valve | Major service part | $$ | Moderate |
| Pressure transducer Verify against a calibrated gauge after replacement. | Periodic replacement | $$ | Moderate |
| Connecting tubing / connectors | Frequent wear item | $ | Easy |
| Alarm / control board | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
Error Codes
Extracted directly from this unit's own service manual.
E0001EEPROM/ROM fail detected. The EEPROM/ROM access was attempted or R/W error occurred. The unit has shut down in a safe state.
Microprocessor failed a ROM memory check. An attempt was made to access or R/W to ROM (non‐volatile memory) and the values were lost. Cycle the ON/ STANDBY button. If problem persists, note error code and contact manufacturer. If problem persists, service the unit.
E0002Valve fail detected. The unit has detected an improper valve combination or missing valve/open valve. The unit has shut down in a safe state.
A valve has failed during operation. A Saf...
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: No or low RF output / high-impedance cut-out
- Confirm good electrode-tissue contact and an adequately wetted field.
- Inspect the handpiece / instrument and its cable for damage; substitute a known-good one.
- Check the split dispersive (return) pad is well applied over well-perfused muscle with a sound cable.
- Verify output into a resistive test load with an electrosurgical analyser.
- Replace the RF output board and recalibrate on a non-conductive surface if output is confirmed absent (anti-static handling).
Symptom: Return-electrode (REM / NESSY / CQM) contact-quality alarm
- Re-apply a fresh split dispersive pad with full skin contact.
- Check the pad cable and its connector.
- Try a known-good pad.
- Run the contact-quality-monitor calibration with a good pad fitted.
- Refer the CQM circuit if it still alarms.
Symptom: Output will not activate from the footswitch or handswitch
- Test the other activation method to isolate the pedal from the handpiece.
- Inspect the footswitch and its cable / connector for damage or moisture.
- Check the handswitch leads on the handpiece.
- Substitute a known-good footswitch.
- Refer the activation input board if both methods fail.
Symptom: Fails calibration / output drifts after a repair
- Verify cut and coag output at several settings into a test load with an analyser.
- Verify the REM / CQM circuit against its spec.
- Recalibrate per the service manual on a non-conductive bench with anti-static precautions.
- Check the cooling fan and thermal path.
- Re-verify all outputs and the REM alarm before returning to service.