Critikon Dinamap Pro 1000
Critikon · Model Dinamap Pro 1000
Unparalleled cardiac monitoring provides accurate data, helping you quickly make the best care decision. Legendary Marquette® ECG with EK-Pro™ and respirations offer comfort that lethal arrhythmias willbe brought to your attention. DINAMAP ASAP technology for accurate and reliable non-invasive BP monitoring. Configurations available with one of the following SpO2 solutions: Masimo® SET® (Gold Standard) or Nellcor OxiMax™. Configurations available with IVAC® TurboTemp™ for temperature in seconds.
Key tips
- ·A no-signal/flatline alarm gets checked on the patient first, not the monitor - rule out a real clinical event before troubleshooting.
- ·Recalibrate NIBP against a reference manometer, not just a self-test pass.
- ·Reused patient cables (SpO2, ECG leads) are a common source of intermittent-fault complaints - swap the cable before the module.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
NIBP will not measure or is inaccurate
HighSymptoms: NIBP times out, cuff will not inflate / hold, readings implausible or fail against a reference.
Root cause: Internal NIBP pump or valve, a cuff / hose leak, or a pressure-transducer / calibration fault.
SpO2 no signal / inaccurate
MediumSymptoms: No saturation value or a poor pleth with a good site.
Root cause: Worn SpO2 sensor / cable, or the SpO2 module.
Temperature channel fault
MediumSymptoms: No or implausible temperature.
Root cause: Probe or cable fault.
Battery / power fault
MediumSymptoms: Short battery run time, will not power on or charge.
Root cause: Aged battery pack.
Printer / recorder fault
LowSymptoms: No or faint strip, paper jam.
Root cause: Thermal print head or paper handling.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Patient cable set (ECG / IBP / SpO2 / temp)
Class Frequent wear itemRel. cost $$R&R Easy
NIBP cuff and hose
Class Frequent wear itemRel. cost $R&R Easy
Internal NIBP pump / valve
Class Major service partRel. cost $$$R&R Difficult
SpO2 sensor / cable
Class Frequent wear itemRel. cost $$R&R Easy
Battery pack
Class Periodic replacementRel. cost $$R&R Fairly easy
Thermal print head / paper
Class Periodic replacementRel. cost $R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Patient cable set (ECG / IBP / SpO2 / temp) | Frequent wear item | $$ | Easy |
| NIBP cuff and hose | Frequent wear item | $ | Easy |
| Internal NIBP pump / valve | Major service part | $$$ | Difficult |
| SpO2 sensor / cable | Frequent wear item | $$ | Easy |
| Battery pack | Periodic replacement | $$ | Fairly easy |
| Thermal print head / paper | Periodic replacement | $ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Routine cable and lead-wire inspection for fraying/wear
- ·Battery conditioning cycle
- ·NIBP calibration check against a reference manometer
- ·ECG / SpO2 accuracy verification against a patient simulator
- ·Annual electrical safety test
Error Codes
Extracted directly from this unit's own service manual.
< 00:30 BATTERY30 minutes remaining in battery life
< 00:10 BATTERY10 minutes remaining in battery life
SHUTTING DOWN< 1 minute remaining in battery life. Monitor may shut down anytime after 45-60 seconds
CHECK COOLING FANMonitor's internal temperature is too high. Cooling fan may be blocked or inoperative
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: NIBP problem
- Leak-test the cuff and hose.
- Run the monitor's NIBP calibration verification.
- Check for a kinked hose or a positional patient limb.
- Verify NIBP against a reference / simulator.
- Refer the monitor for internal pump / valve service if it persists.
Symptom: SpO2 no signal
- Fit a fresh SpO2 sensor and check the site.
- Swap the SpO2 cable.
- Confirm the pleth and signal-quality indicator.
- Replace the SpO2 module if a good sensor and cable do not fix it.
- Verify against a simulator.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- ICU / CCU
- Emergency Department
- OR / PACU
- General med-surg floors
- Step-down units
- Telemetry units
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio