Winco 6570
Winco · Model 6570
Standard headrest cover. Padded drop-down armrests. Dual fold down side-tables. Easy-to-clean side panels. Trendelenburg Positioning.
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
A powered function will not run
HighSymptoms: Height / back / tilt does not respond to the hand or foot control.
Root cause: Foot / hand control fault, a linear actuator, a control-box relay, or a limit switch.
Section drifts or will not hold
MediumSymptoms: Table settles under load after positioning.
Root cause: Actuator backdrive or a gas-spring fault.
Control unresponsive
MediumSymptoms: Intermittent or dead hand / foot control.
Root cause: Cable, contacts, or fluid ingress.
Noisy or slow movement
LowSymptoms: Rumble or sluggish travel.
Root cause: Worn actuator or unlubricated joints.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Linear actuator
Class Major service partRel. cost $$$R&R Moderate
Hand / foot control
Class Periodic replacementRel. cost $$R&R Fairly easy
Control box / relay
Class Major service partRel. cost $$$R&R Moderate
Gas spring (back assist)
Class Major service partRel. cost $R&R Moderate
Limit switch
Class Major service partRel. cost $R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Linear actuator | Major service part | $$$ | Moderate |
| Hand / foot control | Periodic replacement | $$ | Fairly easy |
| Control box / relay | Major service part | $$$ | Moderate |
| Gas spring (back assist) | Major service part | $ | Moderate |
| Limit switch | Major service part | $ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: A powered function is dead
- Verify mains power and any fuse.
- Operate the function and listen for the actuator; test other functions to isolate.
- Substitute a known-good control.
- Check the limit switches.
- Replace the actuator, control or relay as isolated, then load-test.
Symptom: Section drifts down
- Note how fast it settles and under what load.
- Check the actuator for backdrive and the gas spring.
- Replace the actuator or gas spring.
- Confirm it holds at several positions.
- Re-check limit-switch function.
Technical Specs
- Height
- 49 in
- Length
- 43 in
- Weight
- 411
- Patient Weight Capacity
- 450 lbs
- Width
- 37.75 in
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
No documents available for this device yet.
Safety & Recalls
Synced live from the FDA openFDA API.
- RECALL
Winco Manufacturing LLC is recalling the Care Cliner, XL Care Cliner, Drop Arm Care Cliner, Elite Care Cliner, and XL Elite Care Cliner chairs with nylon casters distributed between 04/01/2009 and 08/31/2009. Certain 5" nylon casters shipped with the chairs may be defective. There is a potential of the caster's axle working itself out of the assembly under unconventional conditions. Should this
- RECALL
Winco Mfg., LLC, Ocala, Florida is recalling their Care Cliner. Due to malfunctioning axles which become lose from the caster assembly. This chair is a multi position recliner with a steel frame used primarily in clinics, hospitals and treatment centers for recovery, dialysis, oncology, examination, infusion. Recalled chairs include the following: Care Cliner, XL Care Cliner, Drop Arm Care Cliner
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio