Armedica AM-300 Treatment Table
Armedica · Model AM-300 Treatment Table
34 oz. Heavy-duty vinyl with Permablok 3(R) bacterial protection. 1” Firm density foam tops. Radiused, seamless corners on upholstered components. Top sections have welded steel support frames. Pivoting joints house hardened steel shoulder bolts with locking nuts to ensure years of trouble-free operation. Footswitch control. Power assisted caster system (unless noted otherwise).
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Powered section will not raise/lower
HighSymptoms: A top section does not move from the footswitch, drifts down under load.
Root cause: Worn linear actuator, footswitch fault, or a control-relay / power-supply fault.
Footswitch control failure
MediumSymptoms: No response or intermittent response from the footswitch, one function dead.
Root cause: Fluid ingress or contact wear in the footswitch, or a damaged cable.
Pivot joint / shoulder-bolt wear
MediumSymptoms: Section play or squeak, locking nut loose, uneven section movement.
Root cause: Worn hardened-steel shoulder bolts or loosened locking nuts at the pivots.
Power-assisted caster fault
LowSymptoms: Caster assist not engaging, table hard to move, caster wobble.
Root cause: Power-assist mechanism or caster bearing wear.
Upholstery / Permablok surface damage
LowSymptoms: Torn or cracked vinyl, exposed foam, loss of the antibacterial coating.
Root cause: Wear, sharps, or aggressive cleaning.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Linear actuator (per powered section)
Class Major service partRel. cost $$$R&R Moderate
Footswitch control
Class Periodic replacementRel. cost $$R&R Fairly easy
Pivot shoulder-bolt / locking-nut kit
Class Major service partRel. cost $R&R Moderate
Power-assist caster assembly
Class Major service partRel. cost $$R&R Moderate
Upholstered top section (Permablok 3 vinyl)
Class Major service partRel. cost $$R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Linear actuator (per powered section) | Major service part | $$$ | Moderate |
| Footswitch control | Periodic replacement | $$ | Fairly easy |
| Pivot shoulder-bolt / locking-nut kit | Major service part | $ | Moderate |
| Power-assist caster assembly | Major service part | $$ | Moderate |
| Upholstered top section (Permablok 3 vinyl) | Major service part | $$ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: A powered section will not move
- Verify mains power and any circuit protection.
- Operate the footswitch for that function and listen for the actuator; test other functions to isolate footswitch vs actuator/board.
- Check for hydraulic/actuator drift under load.
- Substitute a known-good footswitch if that input is suspect.
- Replace the actuator, then load-test the section to its rated capacity.
Symptom: Section has play or squeaks at a pivot
- Identify the loose pivot.
- Check the shoulder bolt and locking nut for wear and torque.
- Re-torque or replace the shoulder-bolt / locking-nut hardware.
- Lubricate per the manufacturer.
- Confirm smooth, quiet movement with no play.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio