KaVo ESTETICA E70/E80 Vision
KaVo · Model ESTETICA E70/E80 Vision
Easy to get into and out of the chair - The new arm rests of the KaVo ESTETICA E70/E80 Vision make it easier for your patients to get into and out of the chair. They easily swing downwards and provide support and security during treat- ment, without you having to forgo freedom of movement. A simple touch - With the new sensitive touch display, your KaVo ESTETICA E70/E80 Vision is more intuitive than ever before! With the touch display and its self-explanatory operating logic, you can access all important functions and information withiout any problems. Before, during and after treatment. The completely new design of the user interface was specially developed to aid dental workflow. It is clearly designed, logically structured and ensures that you will find it easy to use at all times. Sensitive touch display for quick access to all important functions and information > Completely new designed user interface > To aid dental workflow > Extreme easy to use > Logically structured > Further functions can be reached by tabs > Homescreen can be inidividually adapted > Sounddesign supports your workflow.
Key tips
- ·Biological-indicator verification applies to dental sterilizers exactly the same as hospital CSSD - no exception for smaller units.
- ·"Sounds different" is often the first real report of handpiece bearing wear, not an outright failure - investigate early rather than waiting.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Motor / actuator / drive will not run or is weak
HighSymptoms: Traction force not applied, CPM carriage will not move or stalls, drive assist weak, motion one direction only.
Root cause: Worn drive motor / leadscrew / actuator, a hand-control fault, or a control-board fault.
Force / range / position inaccuracy
MediumSymptoms: Set traction force or CPM angle not reached, load cell drifts, carriage overshoots or stalls short.
Root cause: Load-cell / position-sensor drift, a potentiometer fault, or a limit-switch fault.
Hand control / patient-control fault
MediumSymptoms: Hand control unresponsive, the patient stop / reverse button does not work.
Root cause: Worn hand control or a damaged cable.
Frame / bearing / cable wear
MediumSymptoms: Rough or noisy travel, play in the carriage, frayed traction cord or rope.
Root cause: Worn bearings / slides or a frayed cable / cord.
Power / battery fault
LowSymptoms: Will not power on, short battery run time.
Root cause: Power supply / fuse or an aged battery.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Drive motor / leadscrew / actuator
Class Major service partRel. cost $$$R&R Difficult
Load cell / position sensor / potentiometer
Class Major service partRel. cost $$R&R Moderate
Hand control
Class Periodic replacementRel. cost $$R&R Fairly easy
Bearings / slides / traction cord
Class Periodic replacementRel. cost $$R&R Moderate
Power supply / fuse / battery
Class Major service partRel. cost $R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Drive motor / leadscrew / actuator | Major service part | $$$ | Difficult |
| Load cell / position sensor / potentiometer | Major service part | $$ | Moderate |
| Hand control | Periodic replacement | $$ | Fairly easy |
| Bearings / slides / traction cord | Periodic replacement | $$ | Moderate |
| Power supply / fuse / battery | Major service part | $ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily handpiece lubrication and autoclave cycle verification
- ·Compressor moisture-trap draining
- ·Annual full PM
Error Codes
Extracted directly from this unit's own service manual.
Error 001Display: "Unit Controller not recognised" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 002Display: "Dentist Controller not recognised" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 003Display: "Operating device controller not recognised" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 004Display: "Dentist operating device not recognised" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 005Display: "Chair A1 error (lift motor)" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 006Display: "Chair A2 error (backrest)" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 008Display: "Chair A4A5 error (neck support)" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 010Display message: "Foot control not detected" The wireless foot control is out of range.
▶ Place the wireless foot control in range.
Error 011Display: "I2C water block does not respond" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 012Display: "Assist. operating device is not responding" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 013Display: "Leakage water S7 is active" Water in unit base.
▶ Open the service flap and remove the water.
Error 014Display: "P valve error" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 015Display: "Dentist operating device is not responding" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 016Display: "Instrument control is not responding" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 017Display: "KL is not responding" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 018Display: "Unit 12C error" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 019Display: "Dentist 12C error" Cable or electronics problem.
▶ Turn the device off and on. If the problem still exists, contact a service technician.
Error 020Display message: "Foot control battery" The foot control battery is empty.
▶ Charge battery.
Error 031Display message: "Oxygenal empty"
▶ Insert new Oxygenal bottle.
Error 032Display message: "Oxygenal bottle"
Error 033Display message: "Oxygenal level is low"
▶ Insert new Oxygenal bottle.
Error 034Display message: "Dekaseptol empty"
▶ Fill Dekaseptol.
Error 035Display message: "Request service"
▶ Notify service technician.
Error 036Display message: "Request intensive germ reduction"
▶ Start intensive germ reduction.
Error 037Display message: "Emergency shut-off bowl suction" No vacuum.
▶ Check the functioning of the vacuum exhauster.
Error 038Display message: "Error amalgam separator"
▶ See Instructions for use for the amalgam separator.
Error 039Display message: "Dekaseptol bottle"
▶ Insert DEKASEPTOL bottle.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Motor / actuator / drive will not run or is weak (traction, standing frame, powered rehab)
- Confirm mains / battery and that the patient stop / e-stop is released.
- Try the hand control and, if fitted, the unit buttons to isolate the control.
- Listen for the drive motor and check the leadscrew / cable / rope is not jammed or frayed.
- Check the hand-control cable for damage.
- Replace the hand control, drive motor or control board as isolated.
Symptom: Set force / range / position not reached (traction / CPM)
- Run the calibration / homing routine.
- Check the load cell / position sensor / potentiometer and the limit switches.
- Verify with a known weight (traction) or a goniometer (CPM / ROM).
- Replace the sensor if it drifts.
- Re-verify the range and confirm the patient stop works.
Symptom: Rough travel / play / frayed cord / worn bearings
- Inspect the bearings / slides and the traction cord / rope for wear.
- Check the leadscrew and nut for backlash.
- Re-lubricate per the manual.
- Replace worn bearings / slides / cord.
- Confirm smooth, quiet, safe operation.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Dental operatory
- Oral surgery suite
- CSSD (dental sterilizers)
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio