Verathon BladderScan BVI 6100
Verathon · Model BladderScan BVI 6100
Helps assess urinary retention and postoperative urinary retention (POUR) Helps prevent unnecessary catheterization Helps reduce rates of catheter-associated urinary tract infection (CAUTI) Helps differentiate between types of incontinence to determine appropriate care Helps monitor postoperative recovery Helps improve efficiency of healthcare professionals by reducing costs and saving staff time.
Key tips
- ·Never bypass a radiation interlock to "just get the image" - this is one of the few true zero-tolerance rules in BMET work.
- ·Trend image-quality phantom results over time - drift shows up before an outright failure does.
- ·Portable/mobile units take real physical abuse from transport - check wheel locks and cable strain reliefs more often than fixed units.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Inaccurate or "low confidence" volume
HighSymptoms: Measured bladder volume clearly wrong, repeated low-confidence results, aiming difficulty.
Root cause: Poor probe placement / aim, insufficient gel, patient factors (scar, obesity), or a probe that needs calibration.
Probe fault (dead elements / mechanism)
HighSymptoms: Missing scan planes, noisy image, probe-fault message; the probe mechanical scan does not run.
Root cause: Failed transducer elements or a worn mechanical scan motor / bearing in the probe.
Probe cable / connector fault
MediumSymptoms: Intermittent operation, probe not detected when the cable is flexed.
Root cause: Broken conductors in the probe cable or at the console connector.
Battery / charging fault
MediumSymptoms: Short run time, will not power on, will not charge in the cradle.
Root cause: Aged battery or a cradle / charging-contact fault.
Display / calibration-certification fault
MediumSymptoms: Console display fault, or the annual accuracy certification fails.
Root cause: Display, or a probe / console calibration issue.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Scan probe
Class Periodic replacementRel. cost $$$$R&R Easy
Probe cable / connector
Class Periodic replacementRel. cost $$R&R Fairly easy
Battery
Class Periodic replacementRel. cost $$R&R Easy
Charging cradle
Class Periodic replacementRel. cost $$R&R Easy
Ultrasound gel
Class Frequent wear itemRel. cost $R&R Easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Scan probe | Periodic replacement | $$$$ | Easy |
| Probe cable / connector | Periodic replacement | $$ | Fairly easy |
| Battery | Periodic replacement | $$ | Easy |
| Charging cradle | Periodic replacement | $$ | Easy |
| Ultrasound gel | Frequent wear item | $ | Easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily QC per modality: image-quality phantom test
- ·Tube and detector inspection
- ·Annual state-required radiation safety survey
- ·Vendor-scheduled preventive maintenance
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Inaccurate / low-confidence volume
- Use ample gel and aim the probe toward the bladder (angled slightly caudal), centring the bladder in the aiming display.
- Repeat 2-3 measurements and keep the best-aimed result.
- Perform the probe calibration per the service manual.
- Verify against a bladder phantom of known volume.
- Isolate the fault to the probe or console using the Diagnostics & Troubleshooting chapter.
Symptom: Probe / cable fault
- Flex the probe cable while scanning a phantom, watching for dropouts.
- Inspect the console connector for damage.
- Try a known-good probe if available.
- Replace the probe or cable as isolated.
- Re-certify accuracy against a phantom after any repair.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Radiology / Imaging department
- Emergency Department (portable units)
- Operating Room (C-arms)
- Cath lab
- Bedside ICU (portable X-ray)
Documents & Manuals
Safety & Recalls
Synced live from the FDA openFDA API.
- RECALL
The firm is providing customers with an updated Operations and Maintenance Manual for each of the BladderScan BVI 9600 and AortaScan AMI 9700 devices. The updated Operations and Maintenance Manuals clarify that these devices should not be used for the screening, detection, or diagnosis of abdominal aortic aneurysms (AAAs).
- RECALL
The BladderScan BVI 9600 with AortaScan devices may experience the loss of a factory installed software configuration file which results in a loss of the aorta measurement function.
- RECALL
Three specific issues are being addressed: 1. Calculation and use of an incorrect year in dates after 12/31/2009. 2. Double scans, continuous scans, and double printing. 3. Calibration sensitivity.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio