Valleylab OptiMumm
Valleylab · Model OptiMumm
Quiet- The OptiMumm™ system allows you to effectively filter and remove surgical smoke without creating additional noise in the OR. RapidVac™ System- Synchronize the OptiMumm™ smoke evacuator with your electrosurgical generator, so the smoke evacuator will work automatically when the generator is activated. Efficient-The OptiMumm™ smoke evacuator is designed specifically for use with the AccuVac™ smoke evacuation attachment to effectively capture and filter smoke directly at the surgical site. Convenient-The OptiMumm™ system is designed with an easy to read front panel and a user-friendly interface. The ULPA and prefilter are easy to access and set up. Compact-The OptiMumm™ smoke evacuator integrates conveniently into the OR. The system fits directly on most Valleylab mounting carts, saving valuable OR space. User-Friendly- The filter life indicator is based on airflow, not just time, so you know when to replace the ULPA filter.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Low or no smoke capture
HighSymptoms: Smoke lingers in the field, weak suction at the pencil / wand, capture alarm.
Root cause: Saturated ULPA / charcoal filter, a kinked or blocked hose, or a worn blower.
Filter-life indicator / filter fault
MediumSymptoms: Filter-change warning, reduced airflow.
Root cause: Filter at end of life or not fully seated.
Noisy or weak blower
MediumSymptoms: Rising noise, vibration, airflow falling off over time.
Root cause: Worn blower / turbine bearing.
Auto-activation / footswitch fault
LowSymptoms: Evacuator does not start with the ESU or footswitch.
Root cause: Activation sensor or footswitch fault.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
ULPA + charcoal filter
Consumable.
Class Frequent wear itemRel. cost $$R&R Easy
Blower / turbine unit
Class Major service partRel. cost $$$R&R Difficult
Suction tubing / wand
Class Frequent wear itemRel. cost $R&R Easy
Footswitch / activation sensor
Class Periodic replacementRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| ULPA + charcoal filter Consumable. | Frequent wear item | $$ | Easy |
| Blower / turbine unit | Major service part | $$$ | Difficult |
| Suction tubing / wand | Frequent wear item | $ | Easy |
| Footswitch / activation sensor | Periodic replacement | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Weak smoke capture
- Fit a new ULPA / charcoal filter.
- Check the hose and wand for kinks or blockage.
- Confirm the blower reaches full speed.
- Keep the capture inlet within a few cm of the plume.
- Replace the blower if airflow is still low with a new filter and clear hose.
Symptom: Will not auto-start
- Test manual activation.
- Check the footswitch and its cable.
- Verify the ESU-sense connection.
- Replace the footswitch or activation sensor.
- Confirm reliable start on the intended trigger.
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio