Conmed ClearView
Conmed · Model ClearView
Reduces noise pollution in the Operating Room. Compact, easy-to-integrate design allows for easy placement on shelf, counter, or stacking. System only activates when electrocautery is used for seamless integration with System 5000 ESU and other ESUs. Features three flow settings (Low/Lap, Medium, and High/Turbo) to meet the needs of different procedure types. Three port filter design accommodates a variety of tubing sizes, providing versatility in procedure and accessory setup. Up to 35-hour filter life. Automatically tracking and recording filter life. Advanced, four-stage filtration uses pre-filter, ULPA filter, carbon filter, and expanded foam to protect against particulates and microorganisms.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Low or no suction / capture
HighSymptoms: Plume not captured, weak airflow, blower ramps but flow is low.
Root cause: Loaded ULPA / charcoal filter, a worn blower / turbine, or a leak / kink in the hose.
Filter loaded / end of life
MediumSymptoms: Filter-change alarm, reduced airflow, odour breakthrough.
Root cause: ULPA / activated-charcoal filter at end of its capacity.
Auto-activation / ESU-sync fault
MediumSymptoms: Evacuator does not start with the ESU, or runs continuously.
Root cause: The ESU-sensing cuff / cable or the auto-activation board.
Blower / turbine fault
MediumSymptoms: Noisy, weak, or dead blower even with a new filter.
Root cause: Worn blower / turbine bearings or motor.
Noise / control fault
LowSymptoms: Very loud in use, speed will not adjust.
Root cause: Worn blower or a speed-control fault.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
ULPA / activated-charcoal filter
Class ConsumableRel. cost $$R&R Easy
Blower / turbine assembly
Class Periodic replacementRel. cost $$$R&R Difficult
ESU-sensing cuff / auto-activation board
Class Major service partRel. cost $$R&R Moderate
Hose / wand adapters
Class Frequent wear itemRel. cost $R&R Easy
Speed-control board
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| ULPA / activated-charcoal filter | Consumable | $$ | Easy |
| Blower / turbine assembly | Periodic replacement | $$$ | Difficult |
| ESU-sensing cuff / auto-activation board | Major service part | $$ | Moderate |
| Hose / wand adapters | Frequent wear item | $ | Easy |
| Speed-control board | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Low or no capture
- Fit a fresh filter and confirm the change alarm clears.
- Check the hose and wand for kinks or blockage.
- Confirm the blower spins up to full speed.
- Measure capture at the wand if a meter is available.
- Replace the blower / turbine if flow is low with a new filter.
Symptom: Does not auto-start with the ESU
- Confirm auto-activation mode is selected.
- Check the ESU-sensing cuff is around the correct ESU lead and the cable is intact.
- Test manual mode to confirm the blower works.
- Adjust the activation sensitivity if provided.
- Replace the sensing cuff / auto-activation board as isolated.