UMF 5020 Power Procedure Table
UMF · Model 5020 Power Procedure Table
5020 Power Procedure Table Our most economical, yet fully featured power procedure table, the UMF Medical lowers to a height of 24 inches (61.0cm)from the floor in a reassuring upright chair position. Provides the versatility needed for OB/GYN, dermatology, proctology, minor surgery and urology procedures and exams. The one-touch, four function hand control allows for precise, smooth operation. You can quickly and easily adjust the seat height, tilt angle, backrest angle, and leg section height with the push of a button. A four function programmable foot control is also available for truly hands-free operation. The UMF Medical Ultra Comfort Seamless Top provides security and comfort for patients and also allows for easy cleaning and helps prevent cross-contamination.
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
A powered function will not run
HighSymptoms: Height / back / tilt does not respond to the hand or foot control.
Root cause: Foot / hand control fault, a linear actuator, a control-box relay, or a limit switch.
Section drifts or will not hold
MediumSymptoms: Table settles under load after positioning.
Root cause: Actuator backdrive or a gas-spring fault.
Control unresponsive
MediumSymptoms: Intermittent or dead hand / foot control.
Root cause: Cable, contacts, or fluid ingress.
Stirrup / leg-section fault
LowSymptoms: One-touch stirrups or the leg section will not glide or lock.
Root cause: Worn stirrup track or leg-section pivot.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Electro-mechanical actuator
Class Major service partRel. cost $$$R&R Moderate
Hand / foot control
Class Periodic replacementRel. cost $$R&R Fairly easy
Control box / relay
Class Major service partRel. cost $$R&R Moderate
Back gas spring
Class Major service partRel. cost $R&R Moderate
Stirrup / leg-section hardware
Class Major service partRel. cost $R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Electro-mechanical actuator | Major service part | $$$ | Moderate |
| Hand / foot control | Periodic replacement | $$ | Fairly easy |
| Control box / relay | Major service part | $$ | Moderate |
| Back gas spring | Major service part | $ | Moderate |
| Stirrup / leg-section hardware | Major service part | $ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: A powered function is dead
- Verify mains power and any fuse.
- Operate the function and listen for the actuator; test other functions to isolate the control vs the actuator / box.
- Substitute a known-good hand / foot control.
- Check the limit switches.
- Replace the actuator, control or relay as isolated, then load-test.
Symptom: Section drifts down
- Note how fast it settles and under what load.
- Check the actuator for backdrive and the gas spring.
- Replace the actuator or gas spring.
- Confirm it holds at several positions.
- Re-check limit-switch function.
Technical Specs
- Patient Weight Capacity
- 400 lbs
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio