ExSpiron 2Xi
Senzime AB (Publ.) · Model RMI-54000
A noninvasive device designed to continuously measure a patient's tidal volume, minute ventilation, and respiratory rate via impedance pneumography. Designed to be connected to the ExSpiron PadSet via the ExSpiron Patient Cable, the ExSpiron 2Xi Monitor provides a measurement of a patient's respiratory parameters, while also incorporating alarms. The ExSpiron 2Xi Monitor can be integrated into a medical facility's nurse call system.
Intended use: A mains electricity (AC-powered) device designed to measure continuously a patient's tidal volume (volume of gas inhaled by the patient during each respiration cycle) or minute volume (the tidal volume multiplied by the rate of respiration for 1 minute) for the evaluation of the patient's ventilatory status. It may also be used to measure the tidal volume, minute volume, and respiration rate delivered to a patient via the expiratory ports of resuscitation devices, such as transport ventilators and resuscitators, to evaluate their performance. The device may incorporate high and low tidal volume alarms.
Key tips
- ·Never disable a low-pressure/circuit-disconnect alarm while troubleshooting - silence it, don't disable it.
- ·Verify the O2 supply source and pressure before assuming an internal fault.
- ·Circuit type must match the patient population (adult/pediatric/neonatal) - a mismatched circuit invalidates delivered volumes.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Will not power on or unexpected shutdown
HighSymptoms: The ventilation & respiratory is dead, reboots, or shuts down mid-use.
Root cause: Mains lead / fuse, an aged battery, or a power-supply board fault.
Battery will not hold charge
MediumSymptoms: Short run time on battery; low-battery alarm soon after a full charge.
Root cause: Aged rechargeable battery pack or a charger fault.
Display / control-panel fault
MediumSymptoms: Blank, dim or distorted display; unresponsive keys or touchscreen.
Root cause: Display, backlight, or control-board fault.
Fails self-test or calibration
MediumSymptoms: Power-on self-test or the scheduled performance check fails or is out of tolerance.
Root cause: Sensor drift or an internal board fault; recalibration or repair needed.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Rechargeable battery pack
Class Periodic replacementRel. cost $$R&R Fairly easy
Power supply / mains board
Class Major service partRel. cost $$$R&R Difficult
Display / control-panel assembly
Class Major service partRel. cost $$$R&R Moderate
Cooling fan
Class Major service partRel. cost $R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Rechargeable battery pack | Periodic replacement | $$ | Fairly easy |
| Power supply / mains board | Major service part | $$$ | Difficult |
| Display / control-panel assembly | Major service part | $$$ | Moderate |
| Cooling fan | Major service part | $ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily pre-use check: self-test, circuit integrity, alarm function
- ·Scheduled circuit and inspiratory filter replacement per manufacturer interval
- ·Flow and pressure sensor calibration verification
- ·Battery load test and runtime check
- ·Annual full PM and electrical safety test
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Will not power on
- Confirm the outlet, mains lead and fuse.
- Try on battery, then on mains only, to isolate the supply.
- Look for a power indicator or POST code.
- Replace the fuse / battery / power supply as isolated.
- Run the self-test after any repair.
Symptom: Fails self-test or calibration
- Note the exact failure message / code.
- Power-cycle and repeat the self-test.
- Verify against a reference / simulator where one applies.
- Recalibrate per the service manual.
- Refer the affected board for service if it will not hold calibration.
Technical Specs
- Storage Environment Temperature
- -20°C to 65°C
- Storage Environment Humidity
- 20 Percent (%) Relative Humidity to 80 Percent (%) Relative Humidity
- Storage Environment Atmospheric Pressure
- 80 KiloPascal to 101 KiloPascal
- Handling Environment Temperature
- 5°C to 32°C
- Handling Environment Humidity
- 20 Percent (%) Relative Humidity to 80 Percent (%) Relative Humidity
- Handling Environment Atmospheric Pressure
- 80 KiloPascal to 101 KiloPascal
- MRI safety
- MR Unsafe
- Sterile
- No
- Single use
- No
- Prescription use
- Rx only
- FDA distribution status
- In Commercial Distribution
- Device type (GMDN)
- Monitoring spirometer, electrical
- FDA product classification
- Monitor, Breathing Frequency; Spirometer, Monitoring (W/Wo Alarm)
- Manufacturer support
- 800-213-1324 · info.us@senzime.com
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- ICU / CCU
- Emergency Department
- Operating Room (anesthesia-adjacent)
- NICU
- Respiratory Therapy department
- Patient transport
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio