Invacare Perfecto2 V
Invacare · Model Perfecto2 V
User-friendly design with easy-to-see and understand control panel. Easy access to humidifier bottle and filter. Low noise level allows for use during sleep. Convenient top handle makes it easy to move. Three separate filters assure oxygen purity. Pressure-based system is superior to timing-based systems. Self diagnostic electronics minimize troubleshooting time. Top handle for ease of mobility. Battery-free power loss alarm, Invacare® Sieve-GARD™ Monitor protects sieve from degradation, compressor 35 psi pressure-relief valve and low flow alarm.
Key tips
- ·Don't extend filter/tubing replacement intervals to save cost - this is an infection-control issue, not just a performance one.
- ·Flow accuracy drift is often the earliest sign of a failing sensor, well before an outright alarm.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Low O2 concentration alarm
HighSymptoms: Oxygen-concentration alarm, delivered O2 below spec at flow.
Root cause: Aged sieve beds (molecular sieve), a compressor / valve fault, an air leak, or an inlet-filter blockage.
Compressor fault / will not build pressure
MediumSymptoms: Weak or no flow, compressor noisy or hot, thermal cut-out.
Root cause: Worn compressor / valve heads, or a cooling-fan fault.
Flow-control / flowmeter fault
MediumSymptoms: Flow will not adjust or does not match the setting.
Root cause: Worn flow-control valve or flowmeter.
Filter blockage
MediumSymptoms: Reduced performance, compressor working hard.
Root cause: Dirty gross-particle / cabinet / final bacteria filter.
Excessive noise / vibration
LowSymptoms: Loud operation, rattling.
Root cause: Worn compressor mounts or a loose panel.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Molecular sieve beds
Class Periodic replacementRel. cost $$$R&R Difficult
Compressor / valve-head rebuild kit
Class Periodic replacementRel. cost $$$R&R Difficult
Inlet / cabinet / final filters
Class Frequent wear itemRel. cost $R&R Easy
Flow-control valve / flowmeter
Class Major service partRel. cost $$R&R Moderate
Cooling fan
Class Periodic replacementRel. cost $R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Molecular sieve beds | Periodic replacement | $$$ | Difficult |
| Compressor / valve-head rebuild kit | Periodic replacement | $$$ | Difficult |
| Inlet / cabinet / final filters | Frequent wear item | $ | Easy |
| Flow-control valve / flowmeter | Major service part | $$ | Moderate |
| Cooling fan | Periodic replacement | $ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Filter and tubing replacement
- ·Flow accuracy check
- ·Annual full PM
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Does not reach or hold the set pressure
- Run the device's pressure-verification against a calibrated manometer with a test lung / cap.
- Check for internal leaks and a blocked pressure-sensing line.
- Confirm the mask / circuit is not the leak source.
- Replace the pressure sensor if it fails verification.
- Replace the blower if it cannot meet flow demand.
Symptom: Blower noisy / failing / cannot meet flow
- Listen for bearing rumble or rattle from the blower.
- Check the inlet air filter is clean.
- Confirm no internal air leak.
- Replace the blower / motor assembly.
- Re-verify pressure and flow after replacement.
Symptom: Humidifier fault (no / excessive humidity, water in the tubing)
- Confirm the heater plate warms and the chamber seats fully.
- Inspect the chamber seal and the heated-tube connector.
- Check the humidity setting against ambient conditions.
- Replace the chamber seal or the heated tube.
- Replace the humidifier heater assembly if it will not heat.
Symptom: Therapy / compliance data will not download
- Try a known-good SD card in the correct slot.
- Check the card is not write-protected or corrupt.
- Confirm the wireless module / modem where fitted.
- Read the card on a PC to confirm data is being written.
- Replace the SD card / slot or the wireless module as isolated.
Technical Specs
- Height
- 23 in
- Length
- 12 in
- Weight
- 40 lbs
- Width
- 13 in
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Respiratory Therapy department
- Patient floors
- Emergency Department
- Home care (portable units)
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio