Hologic Panther Fusion
Hologic · Model Panther Fusion
Up to 32 assay reagent kits on board, which allow assay consolidation on a single platform Ready-to-use reagent cartridges reduce manual preparation and operator errors Sample throughput up to 500 tests in 8 hours increases test volume in a shift without increasing staff Minimal hardware/software changes allow additional testing without extensive retraining or SOP updates.
Key tips
- ·Run QC controls before trusting any repair - an analyzer that passes self-test can still report clinically wrong results.
- ·Rule out a reagent lot change before opening the instrument - it can look exactly like a hardware fault.
- ·Centrifuge rotors have a hard retirement age/cycle limit regardless of visible condition - don't eyeball it.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Sample-transport / track fault
HighSymptoms: Carriers / pucks jam, stall, or mis-route; track-error message; throughput drops.
Root cause: Worn track belts / drive, a diverter / gate fault, or a carrier-sensor fault.
Robotic gripper / pick-place fault
MediumSymptoms: Tubes dropped or mis-placed, gripper-position error, aliquotting mis-aligned.
Root cause: Worn gripper / robot drive or an encoder / home-sensor fault.
Centrifuge module fault
MediumSymptoms: Inline centrifuge imbalance, lid-lock error, will not spin.
Root cause: Drive / bearing wear, a lid-lock fault, or an imbalance-sensor fault.
Decapper / recapper / aliquotter fault
MediumSymptoms: Caps not removed / applied, aliquot volumes off, station jams.
Root cause: Worn decapper jaws, aliquot-probe / syringe wear, or a station-drive fault.
Middleware / connectivity fault
HighSymptoms: Analysers or the LIS drop off the line, rules not applying, samples stuck in a queue.
Root cause: The automation middleware / server or a network link.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Track belts / drive components
Class Periodic replacementRel. cost $$$R&R Difficult
Robotic gripper / drive assembly
Class Periodic replacementRel. cost $$$R&R Difficult
Centrifuge-module drive / lid-lock
Class Periodic replacementRel. cost $$$R&R Difficult
Decapper jaws / aliquot-probe & syringe
Class Periodic replacementRel. cost $$R&R Moderate
Carrier / position sensors
Class Periodic replacementRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Track belts / drive components | Periodic replacement | $$$ | Difficult |
| Robotic gripper / drive assembly | Periodic replacement | $$$ | Difficult |
| Centrifuge-module drive / lid-lock | Periodic replacement | $$$ | Difficult |
| Decapper jaws / aliquot-probe & syringe | Periodic replacement | $$ | Moderate |
| Carrier / position sensors | Periodic replacement | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily QC controls run and reviewed
- ·Calibration verification per assay
- ·Routine cleaning and decontamination
- ·Scheduled reagent-path and pump-tubing maintenance
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Carriers jamming or mis-routing
- Clear the jam and note the station / diverter where it occurs.
- Inspect the track belts and the diverter gates.
- Check the carrier / position sensors are clean and aligned.
- Run the station self-test / calibration.
- Replace the belt, gate or sensor as isolated.
Symptom: Analysers or LIS dropping off the line
- Check the middleware server and its connections to each analyser and the LIS.
- Confirm the network switch / links.
- Restart the affected connection / driver per the OEM procedure.
- Verify rules and routing are active.
- Escalate a middleware-server fault to the OEM / IT.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Central / core laboratory
- Point-of-care testing stations
- Blood bank
- Microbiology lab
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio