A1417MCW
H&abyz Co., Ltd · Model A1417MCW
The A1717MCW/A1417MCW/F1417MCW is a Flat Panel Digital X-ray Detector which have 425.04 x 425.6mm (A1717MCW) or 345.24 x 425.6mm (A1417MCW/F1417MCW) effective pixel area. The device communicates by the wired Ethernet and wireless Wi-Fi communication feature. The detector should be integrated with a Console PC and an X-ray generator to utilize as digitalizing X-ray images and transfer for radiography diagnostic (the Console PC and X-Ray Generator are not provided from H&abyz). The A1717MCW/A1417MCW/F1417MCW consists of the following components: Flat Panel Detector, power supply box, cable, batt
Intended use: An electrically-powered, cassette-like device intended to be used as part of an x-ray system to detect x-ray images following exposure, and create a digital signal; it is not dedicated to imaging of a specific anatomy. It includes two types of transducing technology (i.e., indirect): a scintillator [e.g. caesium iodide (CsI)] screen converts x-ray energy into light, followed by the conversion of light into a digital signal by photodiode array. The image data can be sent to an appropriate processing unit through a wired or wireless connection (e.g., Wi-Fi). It may be used in place of a fixed detector in x-ray imaging systems, e.g., as part of a digital imaging conversion system.
Key tips
- ·Never bypass a radiation interlock to "just get the image" - this is one of the few true zero-tolerance rules in BMET work.
- ·Trend image-quality phantom results over time - drift shows up before an outright failure does.
- ·Portable/mobile units take real physical abuse from transport - check wheel locks and cable strain reliefs more often than fixed units.
Typical Failure Modes
Failure patterns typical of this equipment class - general BMET reference, not verified against this exact unit's own service history unless flagged. Severity is a category-level estimate.
X-ray tube overheating / filament failure
HighSymptoms: Tube won't fire, heat-capacity alarm.
Root cause: Filament wear, cooling failure.
Cooling system fault
HighSymptoms: Tube temp alarm, duty-cycle limited.
Root cause: Pump/radiator or coolant loss.
Generator / high-voltage fault
HighSymptoms: Exposure fails, kV/mA out of range error.
Root cause: HV tank or generator board fault.
Recon / system software hang
LowSymptoms: Frozen console, acquisition timeout.
Root cause: Workstation or RAID degradation.
Serviceable Parts & Consumables
The parts a BMET typically services on this class of equipment. Service class and relative cost are general engineering estimates for the category, not figures from this unit's documentation. Part numbers appear only when pulled from this unit's own service manual. Always confirm intervals and pricing against the manufacturer.
X-ray tube insert
Major R&R; track mAs history.
Class Major service partRel. cost $$$$R&R Expert-level
Flat-panel detector
Class Major service partRel. cost $$$$R&R Expert-level
Cooling pump & radiator
Class Periodic replacementRel. cost $$$R&R Difficult
High-voltage generator
Class Major service partRel. cost $$$$R&R Expert-level
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| X-ray tube insert Major R&R; track mAs history. | Major service part | $$$$ | Expert-level |
| Flat-panel detector | Major service part | $$$$ | Expert-level |
| Cooling pump & radiator | Periodic replacement | $$$ | Difficult |
| High-voltage generator | Major service part | $$$$ | Expert-level |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily QC per modality: image-quality phantom test
- ·Tube and detector inspection
- ·Annual state-required radiation safety survey
- ·Vendor-scheduled preventive maintenance
Troubleshooting Approach
A structured starting point derived from the failure modes above. Follow the manufacturer's service documentation for the actual procedure.
Symptom: X-ray tube overheating / filament failure
- Confirm the presentation - typically tube won't fire, heat-capacity alarm - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: filament wear, cooling failure.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the x-ray tube insert per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Symptom: Detector calibration drift
- Confirm the presentation - typically image noise, artifacts, low SNR - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: flat-panel / sensor aging.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the flat-panel detector per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Technical Specs
- Handling Environment Temperature
- 10°C to 35°C
- Handling Environment Humidity
- 20 Percent (%) Relative Humidity to 75 Percent (%) Relative Humidity
- Handling Environment Atmospheric Pressure
- 70 KiloPascal to 106 KiloPascal
- Storage Environment Temperature
- -15°C to 55°C
- Storage Environment Humidity
- 10 Percent (%) Relative Humidity to 95 Percent (%) Relative Humidity
- Storage Environment Atmospheric Pressure
- 50 KiloPascal to 106 KiloPascal
- MRI safety
- Labeling does not contain MRI Safety Information
- Sterile
- No
- Single use
- No
- Prescription use
- Rx only
- FDA distribution status
- In Commercial Distribution
- Device type (GMDN)
- Indirect flat panel x-ray detector
- FDA product classification
- Solid State X-Ray Imager (Flat Panel/Digital Imager)
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Radiology / Imaging department
- Emergency Department (portable units)
- Operating Room (C-arms)
- Cath lab
- Bedside ICU (portable X-ray)
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio →