Draeger Oxylog 2000 Plus
Dräger · Model Oxylog 2000 Plus
Built for demanding situations - In the field and in emergency situations, reliability, rugged design and simple operation are vital factors for success. The Dräger Oxylog® 2000 plus was designed to provide the caregiver with powerful and flexible ventilation capabilities under the most demanding conditions. Intuitive user interface - The large display gives you clear and highly visible information on clinical values, airway pressure and parameter settings, allowing rapid evaluation of the patients condition during hectic situations. Intuitive controls enable operation within seconds after starting the device. Standardised equipment - The Oxylog® 2000 plus uses the same standardised reusable and disposable hoses as the Oxylog® 3000, letting you simplify your inventory and workflow. Ventilation essentials at your fingertips - The Oxylog® 2000 plus gives you not only a selection of volume-controlled modes but also offers support modes for both invasive and non-invasive ventilation. Pressure Support and Non-Invasive Ventilation are available, enabling support for patients with insufficient breathing and to help prevent intubation at the earliest stage possible. Rugged, compact and highly portable - Easy to carry and simple to mount, the Oxylog® 2000 plus was specifically designed to be taken nearly anywhere. Built from extremely durable, high-impact materials, the unit can stand up to even the most challenging environments. The internal battery provides up to 4 hours of autonomous transport capability.
Key tips
- ·Never disable a low-pressure/circuit-disconnect alarm while troubleshooting - silence it, don't disable it.
- ·Verify the O2 supply source and pressure before assuming an internal fault.
- ·Circuit type must match the patient population (adult/pediatric/neonatal) - a mismatched circuit invalidates delivered volumes.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Fails the pre-use self-test / circuit check
HighSymptoms: Self-test fault, circuit-leak or compliance-check failure, will not be released for use.
Root cause: Patient-circuit / expiratory-valve leak, a flow-sensor fault, an O2-cell fault, or an internal pneumatic fault.
Flow / volume delivery inaccurate
HighSymptoms: Delivered tidal volume or flow does not match the setting, or fails the annual verification.
Root cause: Flow-sensor drift / contamination, an inspiratory / expiratory valve fault, or a blender / proportioning-valve fault.
O2 / air supply or blender fault
MediumSymptoms: Low-supply alarm, FiO2 not matching the setting, O2-cell reads wrong.
Root cause: Wall / cylinder supply issue, an inlet filter / regulator fault, the blender, or an aged O2 cell.
PEEP not held / high circuit pressure
MediumSymptoms: PEEP drifts, auto-PEEP, high-pressure alarms, poor exhalation.
Root cause: Worn or wet expiratory valve / diaphragm, or a blocked exhalation path.
Battery / power fault
MediumSymptoms: Short internal-battery run time, will not charge, transfers to battery unexpectedly.
Root cause: Aged internal battery or a power-supply fault.
Turbine / compressor fault (turbine units)
MediumSymptoms: Noisy operation, cannot meet flow demand, turbine / compressor alarm.
Root cause: Worn turbine / compressor.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Flow sensor(s)
Class Frequent wear itemRel. cost $$R&R Fairly easy
Expiratory valve / diaphragm
Class Frequent wear itemRel. cost $$R&R Fairly easy
O2 cell / sensor
Class Frequent wear itemRel. cost $$R&R Easy
Internal battery
Class Periodic replacementRel. cost $$R&R Fairly easy
Inlet filters / water traps
Class Frequent wear itemRel. cost $R&R Easy
Turbine / compressor (turbine units)
Class Major service partRel. cost $$$$R&R Difficult
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Flow sensor(s) | Frequent wear item | $$ | Fairly easy |
| Expiratory valve / diaphragm | Frequent wear item | $$ | Fairly easy |
| O2 cell / sensor | Frequent wear item | $$ | Easy |
| Internal battery | Periodic replacement | $$ | Fairly easy |
| Inlet filters / water traps | Frequent wear item | $ | Easy |
| Turbine / compressor (turbine units) | Major service part | $$$$ | Difficult |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily pre-use check: self-test, circuit integrity, alarm function
- ·Scheduled circuit and inspiratory filter replacement per manufacturer interval
- ·Flow and pressure sensor calibration verification
- ·Battery load test and runtime check
- ·Annual full PM and electrical safety test
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Fails the pre-use self-test / circuit check
- Run the self-test with the exact circuit, filter and humidifier that will be used.
- Leak-test the circuit and the expiratory valve; fit fresh flow sensors and an O2 cell if due.
- Repeat the self-test and note which check fails.
- Calibrate the flow sensors and O2 cell per the manual.
- Remove from service and refer an internal pneumatic fault to the OEM / biomed.
Symptom: Delivered tidal volume / flow or FiO2 inaccurate
- Verify tidal volume and flow with a calibrated gas-flow analyser and FiO2 at the wye with an O2 analyser.
- Calibrate the flow sensors and the O2 cell.
- Inspect the inspiratory and expiratory valves / diaphragms.
- Check the air and O2 supply pressures and the inlet filters / water traps.
- Refer the blender / proportioning valve if the mix is still wrong.
Symptom: PEEP not held / high circuit-pressure or auto-PEEP
- Inspect the expiratory valve / diaphragm for wear or moisture and replace it.
- Check the exhalation path and the expiratory flow sensor.
- Confirm the circuit and water trap are not obstructed.
- Run the valve / compliance calibration.
- Re-verify PEEP against the analyser.
Symptom: Low-supply / O2 alarm or turbine / compressor fault
- Confirm wall / cylinder supply pressure and the inlet hose and filter.
- Check the internal blender / regulator.
- For a turbine unit, listen for turbine noise and check it can meet flow demand.
- Replace the O2 cell if the FiO2 reading is the issue.
- Refer the turbine / compressor for replacement if it cannot meet demand.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- ICU / CCU
- Emergency Department
- Operating Room (anesthesia-adjacent)
- NICU
- Respiratory Therapy department
- Patient transport
Documents & Manuals
Related calculators
From BioLab, for work done with this kind of equipment.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio