Diapath DIAforceps Advance
Diapath · Model DIAforceps Advance
Steady forceps temperature according to value set by the operator Electronic control unit mod. ADVANCE for forceps thermoregulation Electronic forceps, made of insulating and thermo resistant material with brass tips, 2 mm.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Reagent / paraffin transfer or handling fault
HighSymptoms: Stations not filling or draining, retort not filling (processor), transport arm mis-places baskets, error alarm halts the run.
Root cause: Worn pump / valve, a blocked line, a level-sensor fault, or a transport-drive / gripper fault.
Retort / chamber pressure or vacuum fault (processor)
MediumSymptoms: Pressure / vacuum not achieved, poor infiltration, seal alarm.
Root cause: Worn retort door seal, a vacuum / pressure-pump fault, or a valve.
Poor or inconsistent staining
MediumSymptoms: Slides over- / under-stained, uneven, station-time drift.
Root cause: Exhausted reagents, wrong programme, incorrect agitation, or a timing / arm fault.
Heater / paraffin-bath / oven fault
MediumSymptoms: Paraffin not molten or too hot, oven not at temperature, bath alarm.
Root cause: Heater or temperature-sensor fault.
Fume-extraction / carbon-filter fault
LowSymptoms: Reagent fumes in the room, filter-change overdue.
Root cause: Saturated carbon filter or a fan fault.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Reagent / paraffin pump & valves
Class Periodic replacementRel. cost $$$R&R Difficult
Retort / reagent-vessel seals
Class Periodic replacementRel. cost $$R&R Fairly easy
Transport-arm drive / gripper (stainer)
Class Periodic replacementRel. cost $$$R&R Difficult
Bath / oven heater & temperature sensor
Class Major service partRel. cost $$R&R Moderate
Activated-carbon fume filter
Class Frequent wear itemRel. cost $R&R Easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Reagent / paraffin pump & valves | Periodic replacement | $$$ | Difficult |
| Retort / reagent-vessel seals | Periodic replacement | $$ | Fairly easy |
| Transport-arm drive / gripper (stainer) | Periodic replacement | $$$ | Difficult |
| Bath / oven heater & temperature sensor | Major service part | $$ | Moderate |
| Activated-carbon fume filter | Frequent wear item | $ | Easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Error alarm halts a run
- Note the alarm / error code and check the history log.
- Confirm reagent, paraffin and water levels and correct vessel placement.
- Check the affected station / retort fills and drains fully.
- Inspect seals and the transport arm.
- Follow the service manual for the specific alarm; replace the pump, valve or seal as isolated.
Symptom: Poor or inconsistent staining / processing
- Confirm the correct programme and station times.
- Fit fresh reagents and confirm fill levels.
- Check agitation / dwell and the water supply where used.
- Run a control slide / block and compare to a reference.
- Escalate a timing or transport-arm fault to the OEM.
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio