CareFusion Nicolet EEG Wireless Amplifier
CareFusion · Model Nicolet EEG Wireless Amplifier
The Nicolet Wireless Amplifier features 24 referential, 4 differential, 4 DC and built-in Oximetry channel, enabling use for a variety of video EEG and LTM studies in ambulatory or clinical settings. Connecting to an acquisition computer through a standard high–speed USB 2.0 cable eliminates the need for expensive proprietary cables and allows uploading of 24 hours of data from the amplifier to the station in less than 5 minutes (depending on sampling rates). The NicoletOne multimodality software brings you a dynamic user interface that supports lab efficiency and productivity in a single system or an enterprise network with satellite locations. The NicVue 3.0 SQL data management system coupled with our HL7 interface options and VLink support system provide pioneering resolutions to assist you in providing quality patient care.
Key tips
- ·Electrode impedance drives data quality more than almost any other single factor - check it before assuming an amplifier fault.
- ·Pre-case verification of intraoperative monitoring equipment isn't optional - a mid-case failure has direct surgical-decision consequences.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Noisy / high-impedance channels
HighSymptoms: Mains hum, drift or flat channels, persistently high electrode impedance, poor recording quality.
Root cause: Electrode / lead-wire wear, the electrode box (headbox) inputs, or poor skin prep / environment.
Headbox / amplifier fault
MediumSymptoms: A block of channels dead or saturated regardless of electrode, calibration / bio-cal fails.
Root cause: Headbox amplifier or its cable to the acquisition unit.
Amplifier-to-PC link / acquisition fault
MediumSymptoms: Recording drops, amplifier not detected, data gaps.
Root cause: USB / fibre / network link or a driver.
Photic stimulator / video / audio fault (diagnostic EEG/PSG)
LowSymptoms: Photic strobe not firing, no synchronised video, no audio.
Root cause: Photic lamp / trigger, the video camera, or the audio path.
PSG sensor fault (airflow / effort / SpO2 / limb)
LowSymptoms: A PSG channel (thermistor, pressure, RIP belt, SpO2, PLM) flat or noisy.
Root cause: Worn PSG sensor or its cable.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Electrode lead set / headbox leads
Class Frequent wear itemRel. cost $$R&R Easy
Headbox / amplifier
Class Major service partRel. cost $$$R&R Moderate
Amplifier link cable / interface
Class Periodic replacementRel. cost $$R&R Fairly easy
Photic stimulator lamp (diagnostic)
Class Periodic replacementRel. cost $$R&R Fairly easy
PSG sensor set (airflow / effort / SpO2)
Class Frequent wear itemRel. cost $$R&R Easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Electrode lead set / headbox leads | Frequent wear item | $$ | Easy |
| Headbox / amplifier | Major service part | $$$ | Moderate |
| Amplifier link cable / interface | Periodic replacement | $$ | Fairly easy |
| Photic stimulator lamp (diagnostic) | Periodic replacement | $$ | Fairly easy |
| PSG sensor set (airflow / effort / SpO2) | Frequent wear item | $$ | Easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Electrode / lead impedance check
- ·Amplifier calibration
- ·Annual electrical safety test
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Noisy or high-impedance channels
- Check and re-prep electrode sites; confirm impedances are balanced and low.
- Swap the affected leads and try different headbox inputs.
- Run the bio-calibration / calibration signal.
- Address mains interference (route cables, check the ground).
- Replace the lead set or headbox as isolated.
Symptom: Amplifier not detected / recording drops
- Reseat the amplifier-to-PC link at both ends.
- Restart the acquisition software and amplifier.
- Try a different port / cable.
- Update the driver / firmware if indicated.
- Replace the link cable or refer the amplifier.
Technical Specs
- Weight
- 1.75 lbs
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Neurology / EEG lab
- ICU (continuous EEG monitoring)
- Operating Room (intraoperative monitoring)
Documents & Manuals
Safety & Recalls
Synced live from the FDA openFDA API.
- RECALL
Under certain work flow processes, when selecting a new patient name in NicVue, the associated exams list may not properly refresh, and may continue to display the previous patient's exams.
- RECALL
CareFusion is recalling the NicoletOne Software v5.60.2-5.71.4 used with the Cortical Stimulator Control Unit. It is possible that during cortical stimulation the electrode annotation label may be incorrect on the screen and in the report when the current is correctly delivered through the selected electrodes. Also, it has been determined that the stimulus cable connection in the Cortical S
Related calculators
From BioLab, for work done with this kind of equipment.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio