Buffalo Filter PlumeSafe TURBO Auto-Sense
Buffalo Filter · Model PlumeSafe TURBO Auto-Sense
Extremely Quiet Interactive LCD Screen Auto-Sense RFID technology automatically tracks and records filter life so you don't have to! (patent pending) Provides 0.12 micron filtration @ 99.9995% efficiency TURBO feature allows for an immediate increase in suction Simple filter changes Pneumatic Footswitch Included Isolation Transformer Circuit Compatible.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Low or no suction / capture
HighSymptoms: Plume not captured, weak airflow, blower ramps but flow is low.
Root cause: Loaded ULPA / charcoal filter, a worn blower / turbine, or a leak / kink in the hose.
Filter loaded / end of life
MediumSymptoms: Filter-change alarm, reduced airflow, odour breakthrough.
Root cause: ULPA / activated-charcoal filter at end of its capacity.
Auto-activation / ESU-sync fault
MediumSymptoms: Evacuator does not start with the ESU, or runs continuously.
Root cause: The ESU-sensing cuff / cable or the auto-activation board.
Blower / turbine fault
MediumSymptoms: Noisy, weak, or dead blower even with a new filter.
Root cause: Worn blower / turbine bearings or motor.
Noise / control fault
LowSymptoms: Very loud in use, speed will not adjust.
Root cause: Worn blower or a speed-control fault.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
ULPA / activated-charcoal filter
Class ConsumableRel. cost $$R&R Easy
Blower / turbine assembly
Class Periodic replacementRel. cost $$$R&R Difficult
ESU-sensing cuff / auto-activation board
Class Major service partRel. cost $$R&R Moderate
Hose / wand adapters
Class Frequent wear itemRel. cost $R&R Easy
Speed-control board
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| ULPA / activated-charcoal filter | Consumable | $$ | Easy |
| Blower / turbine assembly | Periodic replacement | $$$ | Difficult |
| ESU-sensing cuff / auto-activation board | Major service part | $$ | Moderate |
| Hose / wand adapters | Frequent wear item | $ | Easy |
| Speed-control board | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: No or low RF output / high-impedance cut-out
- Confirm good electrode-tissue contact and an adequately wetted field.
- Inspect the handpiece / instrument and its cable for damage; substitute a known-good one.
- Check the split dispersive (return) pad is well applied over well-perfused muscle with a sound cable.
- Verify output into a resistive test load with an electrosurgical analyser.
- Replace the RF output board and recalibrate on a non-conductive surface if output is confirmed absent (anti-static handling).
Symptom: Return-electrode (REM / NESSY / CQM) contact-quality alarm
- Re-apply a fresh split dispersive pad with full skin contact.
- Check the pad cable and its connector.
- Try a known-good pad.
- Run the contact-quality-monitor calibration with a good pad fitted.
- Refer the CQM circuit if it still alarms.
Symptom: Output will not activate from the footswitch or handswitch
- Test the other activation method to isolate the pedal from the handpiece.
- Inspect the footswitch and its cable / connector for damage or moisture.
- Check the handswitch leads on the handpiece.
- Substitute a known-good footswitch.
- Refer the activation input board if both methods fail.
Symptom: Fails calibration / output drifts after a repair
- Verify cut and coag output at several settings into a test load with an analyser.
- Verify the REM / CQM circuit against its spec.
- Recalibrate per the service manual on a non-conductive bench with anti-static precautions.
- Check the cooling fan and thermal path.
- Re-verify all outputs and the REM alarm before returning to service.