Vivo 45 LS
Breas Medical AB · Model 006710
Cable, external DC to Ventilator Adapter.
Intended use: A non-patient-contact, insulated, electrical cord with a connector (plug) at both ends designed to transmit electrical power and/or signal (data) between medical devices (e.g., to connect a lead, electrical catheter, handpiece, or monitor to a parent device). It is not intended to connect directly to patient-worn electrodes (i.e., it is not a lead), is not intended to connect to the mains (i.e., not a mains power cable), does not generate any type of power and/or signal, and has no additional non-electrical conducting or processing functionality. This is a reusable device.
Key tips
- ·Never disable a low-pressure/circuit-disconnect alarm while troubleshooting - silence it, don't disable it.
- ·Verify the O2 supply source and pressure before assuming an internal fault.
- ·Circuit type must match the patient population (adult/pediatric/neonatal) - a mismatched circuit invalidates delivered volumes.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Pressure / volume delivery not meeting target
HighSymptoms: Low tidal volume or pressure alarms, patient not adequately ventilated.
Root cause: Circuit leak or disconnect, an exhalation-valve fault, or a blower / flow-sensor fault.
Flow / pressure sensor drift
MediumSymptoms: Monitored values implausible, nuisance alarms, fails a calibration check.
Root cause: Proximal flow sensor or internal pressure transducer aging.
Battery will not hold charge
HighSymptoms: Short internal-battery run time.
Root cause: Aged internal or detachable battery.
Blower / turbine wear
MediumSymptoms: Noise, reduced peak flow, blower alarm.
Root cause: Worn blower bearing.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Air-inlet filter
Class ConsumableRel. cost $R&R Easy
Proximal flow sensor
Class Frequent wear itemRel. cost $$R&R Easy
Exhalation valve / circuit
Class Frequent wear itemRel. cost $R&R Easy
Internal / detachable battery
Class Periodic replacementRel. cost $$R&R Fairly easy
Blower / turbine
Class Major service partRel. cost $$$R&R Difficult
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Air-inlet filter | Consumable | $ | Easy |
| Proximal flow sensor | Frequent wear item | $$ | Easy |
| Exhalation valve / circuit | Frequent wear item | $ | Easy |
| Internal / detachable battery | Periodic replacement | $$ | Fairly easy |
| Blower / turbine | Major service part | $$$ | Difficult |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily pre-use check: self-test, circuit integrity, alarm function
- ·Scheduled circuit and inspiratory filter replacement per manufacturer interval
- ·Flow and pressure sensor calibration verification
- ·Battery load test and runtime check
- ·Annual full PM and electrical safety test
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Not meeting target pressure / volume
- Perform the ventilator pre-use check and circuit test.
- Leak-test the patient circuit and check the exhalation valve.
- Fit a fresh flow sensor and re-run the check.
- Confirm the correct circuit type and settings.
- Replace the blower if peak flow is low with a sealed circuit.
Symptom: Short battery run time
- Fully charge and note the run time.
- Test the detachable battery separately.
- Replace the aged battery.
- Confirm the charging indicator.
- Re-verify run time.
Technical Specs
- MRI safety
- Labeling does not contain MRI Safety Information
- Sterile
- No
- Single use
- No
- Prescription use
- Rx only
- FDA distribution status
- In Commercial Distribution
- Device type (GMDN)
- Electrical-only medical device connection cable, reusable
- FDA product classification
- Ventilator, Continuous, Facility Use; Continuous, Ventilator, Home Use
- Manufacturer support
- 855-436-8724 · supportUS@breas.com
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- ICU / CCU
- Emergency Department
- Operating Room (anesthesia-adjacent)
- NICU
- Respiratory Therapy department
- Patient transport
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio