Biodex Vasc Pro
Biodex · Model Vasc Pro
Ergonomic design helps prevent musculoskeletal injuries – comfortable shoulder, arm and hand positions when scanning. Extra wide top with 500-lb patient capacity, suitable for bariatric patients. Reverse Trendelenburg to 30 degrees. Height range down to 23″ accommodates wheelchair transfers and those with ambulatory difficulties. Fowler positioning, 0-80 degrees, redesigned to accommodate natural body extension and sitting position without slide or shift. Motorized height, Fowler positioning, Trendelenburg and auto-level adjustment. Improved foot support with comfortable access to calves without crouching. Naugahyde®, antimicrobial mattress cover with Advanced BeautyGard® provides protection against bacteria. Central floor-locking system maintains table stability. Durable hand controller. Allows seated or standing work positions.
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
A powered function will not run
HighSymptoms: Height, tilt / Trendelenburg, back or the imaging drop-section does not respond to the foot or hand control.
Root cause: Foot / hand control fault, a linear actuator, a control-relay fault, or a limit switch.
Section drifts or will not hold
MediumSymptoms: Table settles under load after positioning.
Root cause: Actuator backdrive or a gas-spring fault.
Control unresponsive
MediumSymptoms: Intermittent or dead foot / hand control.
Root cause: Cable, contacts, or fluid ingress.
Scan-window / drop-section or pelvic-tilt fault
LowSymptoms: The echo / vascular access window or pelvic tilt binds or will not lock.
Root cause: Worn drop-section pivot or lock.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Linear actuator
Class Major service partRel. cost $$$R&R Moderate
Foot / hand control
Class Periodic replacementRel. cost $$R&R Fairly easy
Control relay / board
Class Major service partRel. cost $$R&R Moderate
Gas spring
Class Major service partRel. cost $R&R Moderate
Drop-section / pelvic-tilt hardware
Class Major service partRel. cost $R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Linear actuator | Major service part | $$$ | Moderate |
| Foot / hand control | Periodic replacement | $$ | Fairly easy |
| Control relay / board | Major service part | $$ | Moderate |
| Gas spring | Major service part | $ | Moderate |
| Drop-section / pelvic-tilt hardware | Major service part | $ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: A powered function is dead
- Verify mains power and any fuse.
- Operate the function and listen for the actuator; test other functions to isolate the control vs the actuator.
- Substitute a known-good foot / hand control.
- Check the limit switches.
- Replace the actuator, control or relay as isolated, then load-test.
Symptom: Section drifts down
- Note how fast it settles and under what load.
- Check the actuator for backdrive and the gas spring.
- Replace the actuator or gas spring.
- Confirm it holds at several positions.
- Re-check limit-switch function.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio