ClearView Nasal Mask and Capnography Bundle – Pediatric Groovy Grape (pkg. 12)
ACCUTRON, INC. · Model 33037-17-CAP
ClearView Nasal Mask and Capnography Bundle – Pediatric Groovy Grape (pkg. 12)
Intended use: A flexible, form-shaped device designed to be placed over a patient's nose and/or mouth to direct anaesthetic gases to the upper airway. It is made of conductive or non-conductive rubber, polyvinyl chloride (PVC), or other sterilizable materials that produce a soft, flexible cover to create an airtight seal against the patient's face. It typically includes a 22 mm connector (adult) or a 15 mm connector (paediatric), and is available in a range of sizes. It may be stabilized with a headstrap. This device is sometimes used in association with a manual resuscitator. This is a single-use device.
Key tips
- ·A no-signal/flatline alarm gets checked on the patient first, not the monitor - rule out a real clinical event before troubleshooting.
- ·Recalibrate NIBP against a reference manometer, not just a self-test pass.
- ·Reused patient cables (SpO2, ECG leads) are a common source of intermittent-fault complaints - swap the cable before the module.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Gas readings inaccurate or drifting
HighSymptoms: CO2 / agent / N2O / O2 values biased, will not calibrate, zero drift.
Root cause: Sample-cell / bench contamination, an aged O2 cell, or a calibration-gas / calibration issue.
Sample-line / water-trap occlusion
MediumSymptoms: "Occlusion" or "sample line blocked", low sample flow, no waveform.
Root cause: Blocked sampling line or a saturated / full water trap (Nafion / moisture trap).
Sample pump fault
MediumSymptoms: Low or no sample flow with a clear line, pump noisy or stopped.
Root cause: Worn sample pump.
O2 sensor fault (paramagnetic / galvanic)
MediumSymptoms: O2 reads wrong or will not calibrate.
Root cause: Aged galvanic O2 cell or a paramagnetic-sensor fault.
Module / host-communication fault
LowSymptoms: Host monitor does not see the gas module, intermittent dropout.
Root cause: Module connector / docking or an internal board fault.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Water trap / moisture trap
Class ConsumableRel. cost $R&R Easy
Sampling line
Class ConsumableRel. cost $R&R Easy
Sample pump
Class Periodic replacementRel. cost $$R&R Moderate
O2 sensor / cell
Class Frequent wear itemRel. cost $$R&R Fairly easy
Gas bench / sample cell
Class Major service partRel. cost $$$R&R Difficult
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Water trap / moisture trap | Consumable | $ | Easy |
| Sampling line | Consumable | $ | Easy |
| Sample pump | Periodic replacement | $$ | Moderate |
| O2 sensor / cell | Frequent wear item | $$ | Fairly easy |
| Gas bench / sample cell | Major service part | $$$ | Difficult |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Routine cable and lead-wire inspection for fraying/wear
- ·Battery conditioning cycle
- ·NIBP calibration check against a reference manometer
- ·ECG / SpO2 accuracy verification against a patient simulator
- ·Annual electrical safety test
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Occlusion / low sample flow
- Replace the water trap and the sampling line.
- Run the module's flow / leak check.
- Confirm the exhaust / scavenging return is not blocked.
- Replace the sample pump if flow is still low with a clear path.
- Verify the sample flow rate against the spec.
Symptom: Readings inaccurate or will not calibrate
- Run the span calibration with a certified calibration gas.
- Replace the O2 cell if the O2 channel will not calibrate.
- Check for water / contamination in the bench and dry / purge per the manual.
- Allow the full warm-up time before calibrating.
- Escalate a bench fault to the OEM if calibration still fails.
Technical Specs
- MRI safety
- Labeling does not contain MRI Safety Information
- Sterile
- No
- Single use
- Yes
- Prescription use
- Rx only
- FDA distribution status
- In Commercial Distribution
- Device type (GMDN)
- Anaesthesia face mask, single-use
- FDA product classification
- Mask, Scavenging
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- ICU / CCU
- Emergency Department
- OR / PACU
- General med-surg floors
- Step-down units
- Telemetry units
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio