Avoximeter Whole Blood CO-Oximeter
Avoximeter 4000 Cuvettes 100 cuvettes/box.
Intended use: A substance or reactant intended to be used together with a parent IVD to perform a specific function in an assay that is used for the quantitative measurement of one or multiple blood gas analytes in a clinical specimen.
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Inaccurate / questionable oximetry results
HighSymptoms: tHb, O2Hb, COHb or MetHb values implausible, QC out of range.
Root cause: Dirty or scratched cuvette optics, an air bubble / short sample in the cuvette, lamp aging, or calibration drift.
Lamp / optical source failure
MediumSymptoms: Low signal, will not read, lamp / reference-intensity warning.
Root cause: Optical source at end of life.
Cuvette handling / detection fault
MediumSymptoms: Bubble or short-sample errors, cuvette not detected.
Root cause: Air in the microcuvette, a worn cuvette, or a cuvette-detect sensor fault.
Battery / power fault
LowSymptoms: Will not power on, short battery life (portable models).
Root cause: Depleted or aged battery.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Optical source / lamp
Class Periodic replacementRel. cost $$R&R Moderate
Microcuvettes
Class Frequent wear itemRel. cost $R&R Easy
Optical filter / detector assembly
Class Major service partRel. cost $$$R&R Difficult
Battery (portable models)
Class Periodic replacementRel. cost $$R&R Fairly easy
QC / calibration verification standard
Class Frequent wear itemRel. cost $$R&R Easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Optical source / lamp | Periodic replacement | $$ | Moderate |
| Microcuvettes | Frequent wear item | $ | Easy |
| Optical filter / detector assembly | Major service part | $$$ | Difficult |
| Battery (portable models) | Periodic replacement | $$ | Fairly easy |
| QC / calibration verification standard | Frequent wear item | $$ | Easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Results inaccurate / QC fails
- Run the QC / calibration-verification standard and compare to the assigned values.
- Clean the cuvette optics / detection window.
- Fill a fresh microcuvette avoiding bubbles.
- Replace the lamp if the reference intensity is low.
- Re-verify with QC before reporting patient results.
Symptom: Bubble / short-sample errors
- Refill the cuvette avoiding air.
- Inspect the cuvette for scratches or residue.
- Use a fresh cuvette.
- Confirm the correct sample volume.
- Re-run the sample.
Technical Specs
- MRI safety
- Labeling does not contain MRI Safety Information
- Sterile
- No
- Single use
- Yes
- Prescription use
- Rx only
- FDA distribution status
- In Commercial Distribution
- Device type (GMDN)
- Multiple blood gas analyte IVD, reagent
- FDA product classification
- Spectral Absorb. Curve, Oxyhemoglobin, Carboxyhemoglobin, Carbon-Monoxide
- Manufacturer support
- 1-800-678-0710 · ilsd_ra.na@werfen.com
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio