Yon Don YD-F-285TR
Yon Don · Model YD-F-285TR
Digital microprocessor based control system. 3-Level over-heating protection mechanism. Skin sensor failure detection (only available on 285TRSC). Power failure detection. Reminder audio alerts every 15 minutes if actual air/skin temperature does not reach within 1 degree range of the set temperature. Advanced programmable heating parameters for different ambient conditions. Touch keys for easy control settings. Water-proof control panel film to protect against spills or splashes. Large LED displays for easy readings on incubator status. Durable and transparent acrylic provides great visibility to infant. Convenient access ports reduce air temperature fluctuations. Double-wall minimizes temperature fluctuations (optional feature). Soft mattress provides comfort to the infant. Advanced air circulation system to provides best exchange and distribution of heat and air/oxygen. Spacious compartment provides room for oxygen hood (hood is optional). Convenience ports available to allow secure pathways for skin probes (only available on 285TRSC), oxygen tubes, and etc. Front door allows transporting infant in/out of the incubator with great ease. Tilt-enabled compartment provides maximum access to interior of the compartment.
Key tips
- ·Never skip temperature-accuracy verification to save time - it's the one check that directly prevents burns.
- ·Hose/blanket connector wear is the most common real fault and the easiest to miss on a quick visual check.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Air- or radiant-heater control fault
HighSymptoms: Chamber / patient will not reach or hold the set temperature, temperature alarm, self-test / "Check" fault.
Root cause: Heater element / infrared rod, the air- or skin-temperature sensor, the fan (incubator), or a control-board fault.
Skin-temperature (servo) control fault
HighSymptoms: Servo mode does not regulate to the skin probe, deviation alarm, probe-fault alarm.
Root cause: Damaged skin temperature probe or its connector, or the servo-control circuit.
Alarm / audible / power-fail-alarm fault
MediumSymptoms: No or quiet audible alarm, alarm lamp does not light on the self-test.
Root cause: Buzzer / speaker or the alarm board - a safety-critical failure.
Humidity / airflow fault (incubator)
MediumSymptoms: Set humidity not reached, uneven chamber temperature, airflow alarm.
Root cause: Humidifier reservoir / heater, or a worn circulation fan / blocked air filter.
Mattress / weigh-scale / tilt / access-port fault
LowSymptoms: In-bed scale inaccurate, tilt mechanism stiff, port latches or iris sleeves worn.
Root cause: Load cell, tilt actuator, or worn access-port hardware.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Air / skin temperature sensors
Class Frequent wear itemRel. cost $$R&R Fairly easy
Heater element / infrared rod
Class Major service partRel. cost $$R&R Difficult
Circulation fan (incubator)
Class Major service partRel. cost $$R&R Moderate
Humidifier heater / reservoir (incubator)
Class Periodic replacementRel. cost $$R&R Moderate
Buzzer / alarm board
Class Major service partRel. cost $R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Air / skin temperature sensors | Frequent wear item | $$ | Fairly easy |
| Heater element / infrared rod | Major service part | $$ | Difficult |
| Circulation fan (incubator) | Major service part | $$ | Moderate |
| Humidifier heater / reservoir (incubator) | Periodic replacement | $$ | Moderate |
| Buzzer / alarm board | Major service part | $ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Hose / blanket connector inspection
- ·Temperature-accuracy verification
- ·Annual electrical safety test
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Chamber or patient temperature will not reach / hold the setpoint
- Run the readiness / self-test and confirm the alarm lamp and buzzer.
- Set a target and confirm the unit reaches it; compare to an independent calibrated reference.
- Check the circulation fan runs and the air filter is clean (incubator).
- Verify the heater element / infrared rod draws current.
- Replace the air / skin temperature sensor, the heater element or the infrared rod as isolated.
Symptom: Skin (servo) control does not regulate / probe-fault alarm
- Fit a known-good skin temperature probe with good skin contact.
- Check the probe connector and cable.
- Verify the servo regulates to the probe with a warm reference.
- Replace the probe.
- Refer the servo-control circuit if it still will not regulate.
Symptom: No or quiet audible alarm / alarm lamp fails the self-test
- Run the self-test / check function and watch the alarm lamp and listen for the buzzer.
- Check the buzzer / speaker and its connector.
- Check the alarm board.
- Replace the buzzer or alarm board - a failed alarm is a safety fault.
- Confirm all alarm conditions annunciate before returning to service.
Symptom: Humidity not reached / uneven chamber temperature (incubator)
- Check the humidifier reservoir level and the humidifier heater.
- Confirm the circulation fan runs and the air filter is clean.
- Check for a chamber / access-port seal leak.
- Verify humidity with an independent reference.
- Replace the humidifier heater or the circulation fan as isolated.
Technical Specs
- Height
- 45 cm
- Length
- 76 cm
- Width
- 43 cm
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Operating Room
- PACU
- Emergency Department
- Labor & Delivery
- NICU
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio