Stryker FloControl
Stryker · Model FloControl
• Programmable joint icons change the flow rate and pressure for ideal performance during knee, shoulder and small joint procedures • Wash button quickly clears the joint of debris. Length of wash and pressure increase can vary depending upon surgeon preference • Fluid conservation feature helps maximize OR efficiency and reduce cost • LCD screen display provides easily identifiable digital readout of flow rate, preset and in joint pressure
Key tips
- ·Never defeat or bypass a return-electrode monitoring (REM) alarm to finish a case - it's a direct burn risk.
- ·Verify OR table battery backup - a table that loses power mid-procedure is a real, documented incident type.
- ·Track surgical light lamp-hours rather than waiting for failure - a sudden failure mid-case is avoidable.
Typical Failure Modes
Failure patterns typical of this equipment class - general BMET reference, not verified against this exact unit's own service history unless flagged. Severity is a category-level estimate.
Handpiece motor / coupling wear
HighSymptoms: Weak or stalled blade rotation.
Root cause: Motor brush wear or drive coupling fatigue.
Console circuit board fault
HighSymptoms: Console won't power on, or resets mid-case.
Root cause: Main board or power supply failure.
Footswitch / console control fault
MediumSymptoms: No response, or intermittent activation.
Root cause: Worn footswitch pedal or connector.
RF electrode connector wear (RF-equipped consoles)
MediumSymptoms: Arcing, or no RF output.
Root cause: Worn electrode connector contacts.
Serviceable Parts & Consumables
The parts a BMET typically services on this class of equipment. Service class and relative cost are general engineering estimates for the category, not figures from this unit's documentation. Part numbers appear only when pulled from this unit's own service manual. Always confirm intervals and pricing against the manufacturer.
Console main board
Class Major service partRel. cost $$$R&R Difficult
Handpiece motor assembly
Major R&R; sterilizable handpiece wears fastest.
Class Periodic replacementRel. cost $$$$R&R Difficult
Blade / burr coupling
High-turnover; keep spares.
Class Periodic replacementRel. cost $$R&R Fairly easy
Footswitch / pedal assembly
Class Periodic replacementRel. cost $$R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Console main board | Major service part | $$$ | Difficult |
| Handpiece motor assembly Major R&R; sterilizable handpiece wears fastest. | Periodic replacement | $$$$ | Difficult |
| Blade / burr coupling High-turnover; keep spares. | Periodic replacement | $$ | Fairly easy |
| Footswitch / pedal assembly | Periodic replacement | $$ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Pre-case functional check
- ·Electrosurgical return-electrode cable inspection
- ·Table hydraulic / mechanical inspection
- ·Annual electrical safety test and full PM
Troubleshooting Approach
A structured starting point derived from the failure modes above. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Handpiece motor / coupling wear
- Confirm the presentation - typically weak or stalled blade rotation.
- Check the most likely cause first: motor brush wear or drive coupling fatigue.
- Inspect the affected subsystem against the manufacturer's inspection checklist.
- If the fault is confirmed and not a field adjustment, service or replace the handpiece motor assembly per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Symptom: Console circuit board fault
- Confirm the presentation - typically console won't power on, or resets mid-case.
- Check the most likely cause first: main board or power supply failure.
- Inspect the affected subsystem against the manufacturer's inspection checklist.
- If the fault is confirmed and not a field adjustment, service or replace the blade / burr coupling per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Operating rooms
- Procedure rooms
- Interventional suites
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio →