Schick CDR PanX
Schick · Model CDR PanX
Digital panoramic imaging, designed for enhanced image quality, flexibility and functionality. High quality extra-oral imaging combined with simple operation can easily be integrated into any dental practice. Superior patient positioning system provides clear, crisp, clinically diagnostic images. Superior vertical travel allows proper positioning for patients of virtually any height, including those in wheelchairs. Laser alignment beams enable more concise patient positioning. Increases practice economic efficiency by eliminating costly film processing expense. Seamlessly integrates with world leading CDR intraoral sensors and software. Designed to produce optimal images with every exposure. Four point patient positioning for panoramic imaging insures patient stability. Intuitive control panel design improves workflow and streamlines set-up time. Automatic control of exposure provides optimized anterior imaging.
Key tips
- ·Biological-indicator verification applies to dental sterilizers exactly the same as hospital CSSD - no exception for smaller units.
- ·"Sounds different" is often the first real report of handpiece bearing wear, not an outright failure - investigate early rather than waiting.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
No or inconsistent exposure
HighSymptoms: No image, exposure will not trigger, images consistently under- or over-exposed, error code.
Root cause: Tube-head fault, an exposure-switch / timer fault, HV / generator fault, or a sensor / PSP-plate fault.
Sensor / imaging-plate fault (digital)
MediumSymptoms: Dead lines, artefacts, no image from the sensor, PSP plate scratched / fogged.
Root cause: Damaged intraoral sensor / cable, or worn PSP plates.
Pano / CBCT motion or reconstruction fault
MediumSymptoms: Blurred or distorted panoramic image, layer / focal-trough errors, reconstruction fails.
Root cause: Rotation drive / belt / encoder, patient-positioning error, or the reconstruction PC.
Tube-arm / balance fault
MediumSymptoms: Tube head drifts, will not stay positioned, arm joints loose.
Root cause: Worn arm springs / friction joints.
Software / acquisition fault
LowSymptoms: Images will not acquire, save or display in the practice-management software.
Root cause: TWAIN / driver, the acquisition PC, or the software.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Intraoral sensor & cable / PSP plates
Class Periodic replacementRel. cost $$$R&R Fairly easy
Tube head / HV components
Class Major service partRel. cost $$$$R&R Difficult
Exposure switch / timer board
Class Major service partRel. cost $$R&R Moderate
Pano rotation drive / belt / encoder
Class Major service partRel. cost $$$R&R Difficult
Tube-arm spring / friction-joint kit
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Intraoral sensor & cable / PSP plates | Periodic replacement | $$$ | Fairly easy |
| Tube head / HV components | Major service part | $$$$ | Difficult |
| Exposure switch / timer board | Major service part | $$ | Moderate |
| Pano rotation drive / belt / encoder | Major service part | $$$ | Difficult |
| Tube-arm spring / friction-joint kit | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily handpiece lubrication and autoclave cycle verification
- ·Compressor moisture-trap draining
- ·Annual full PM
Error Codes
Extracted directly from this unit's own service manual.
1Microprocessor error
2EPROM error
4RAM error
7Rotation unit cannot move: stepper motor control error
11Digital imaging software not ready to acquire image
12Invalid limit switch status
13Exposure exceeds maximum time permitted
14X-ray high voltage error
15Undervoltage condition at main power
17Tube filament heating current exceeds range permitted
18No current in X–ray tube
19Exposure switch released during exposure time: incomplete image
20Exposure switch released prior to X-ray emission: exposure was unsuccessful
21Exposure switch released after X-ray emission, but rotation motor movement was not complete
23Rotation unit steps do not match in half of the track
25Rotation unit steps do not match in half of the track
28Rotation unit steps do not match at the end of the track
31Rotation unit does not move
33Tube filament heating current active during off status
34X–ray tube current active during off status
60Control unit microcontroller or memory error
62Software error while Rotation unit is in motion
63Tube head temperature exceeds value permitted
6415V power supply error
6524V power supply error
665V power supply error
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: No or inconsistent exposure / generator or tube-head error
- Note the exact error code and whether it is a kV / mA / preheat / interface failure.
- Check the mains supply, the dedicated circuit and the fuses.
- Check the tube-head and detector / sensor interface cable connections.
- Confirm the exposure switch is held for the full exposure and the warning light works.
- Escalate a confirmed tube-head / HV / generator fault; verify output with a dental X-ray meter after any repair.
Symptom: Blurred or distorted panoramic image / layer or focal-trough errors
- Confirm patient positioning (bite block, chin rest, light guides).
- Check the rotation drive belt, motor and encoder for wear or slip.
- Run any image-calibration / geometry routine.
- Verify the focal-trough / layer selection.
- Escalate a drive / reconstruction fault to the OEM.
Symptom: Sensor / CCD / CBCT detector fault (dead lines, artefacts, no image)
- Swap in a known-good sensor if available.
- Inspect the sensor cable for kinks or breaks.
- Run the detector calibration / dead-pixel map.
- Expose a phantom and check uniformity.
- Replace or refer the detector as isolated.
Symptom: Software / acquisition fault (image will not acquire, save or display)
- Check the TWAIN / driver and the acquisition PC.
- Restart the acquisition software and the unit.
- Confirm the practice-management link.
- Update to compatible driver / software versions.
- Escalate a persistent acquisition fault to the OEM.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Dental operatory
- Oral surgery suite
- CSSD (dental sterilizers)
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio