Quanta System Thulium Fiber Laser
Quanta System · Model Thulium Fiber Laser
Lithotripsy First in vitro and in vivo experiences suggest strong potential for TFL technology in stone ablation. The peak power of TFL enables extremely limited retropulsion, while providing gentle stone dusting and generation of tiny particles. Indeed, TFL technology proved so far as an excellent dusting tool, in particular for low-medium hardness calculi. The wide frequency range (up to 2500 Hz) allows to speed up the treatment once you found the desired pulse energy and pulse duration combination. Fiber Dust further allows full performances already with 200µm core fiber, leaving space for output increase when needed. Additionally, the 150µm fiber allows even greater flexibility and irrigation flow. BPH & Soft Tissue Surgery Thulium wavelength is strongly absorbed by water, allowing efficient and precise ablation and incision of soft tissues. A maximum output power of 60W enables low-power . In particular, with Fiber Dust you can choose between a superpulsed ThuLEP (with higher peak power) and a more traditional continuous emission ThuLEP. Because of its features, Thulium laser can also be used for smooth ablation, resection and incision of urinary soft tissues requiring low-medium power, such as for the treatment of bladder and ureteral tumors, and urethral stricture.
Key tips
- ·Verify true laser output with an external power meter, not the console readout - the display drifts independently of real delivered energy.
- ·Never bypass a door interlock, key switch, or footswitch safety to finish a treatment - laser safety interlocks are not optional.
- ·Most low-output complaints trace to the delivery fiber or handpiece, not the laser source - inspect and swap those first.
- ·Intermittent mid-treatment shutdowns are usually cooling-related - check coolant level and flow before suspecting the diode or lamp.
Typical Failure Modes
Failure patterns typical of this equipment class - general BMET reference, not verified against this exact unit's own service history unless flagged. Severity is a category-level estimate.
Laser diode / gain medium degradation
HighSymptoms: Reduced output power, inconsistent treatment fluence.
Root cause: Normal diode/gain-medium wear over lamp/diode hours.
Cooling system fault
HighSymptoms: Overheat shutdown mid-treatment, error code on startup.
Root cause: Coolant pump, TEC element, or filter degradation.
Handpiece / delivery fiber wear
MediumSymptoms: Uneven beam delivery, connector arcing, or no output at the handpiece.
Root cause: Fiber or articulated-arm optics degraded by flex/heat cycling.
Interlock / shutter fault
MediumSymptoms: Won't fire, safety interlock fault on the display.
Root cause: Door/footswitch interlock or shutter mechanism failure.
Serviceable Parts & Consumables
The parts a BMET typically services on this class of equipment. Service class and relative cost are general engineering estimates for the category, not figures from this unit's documentation. Part numbers appear only when pulled from this unit's own service manual. Always confirm intervals and pricing against the manufacturer.
Handpiece / delivery fiber assembly
High-turnover; keep spares.
Class Periodic replacementRel. cost $$$R&R Fairly easy
Footswitch / interlock assembly
Class Major service partRel. cost $$R&R Fairly easy
Laser diode / flashlamp module
Core consumable; major cost driver.
Class Periodic replacementRel. cost $$$$R&R Difficult
Cooling system (pump / TEC / filter)
Class Periodic replacementRel. cost $$$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Handpiece / delivery fiber assembly High-turnover; keep spares. | Periodic replacement | $$$ | Fairly easy |
| Footswitch / interlock assembly | Major service part | $$ | Fairly easy |
| Laser diode / flashlamp module Core consumable; major cost driver. | Periodic replacement | $$$$ | Difficult |
| Cooling system (pump / TEC / filter) | Periodic replacement | $$$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Laser output power verification against a calibrated external power meter
- ·Cooling-system check: coolant level, flow rate, and filter / heat-exchanger condition
- ·Delivery-system inspection: handpiece, delivery fiber or articulated arm, and output optics
- ·Interlock, key-switch, emergency-stop, and footswitch function test
- ·Beam-alignment and optical-path check per the service manual
- ·Annual full PM and electrical safety test
Troubleshooting Approach
A structured starting point derived from the failure modes above. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Laser diode / gain medium degradation
- Confirm the presentation - typically reduced output power, inconsistent treatment fluence.
- Check the most likely cause first: normal diode/gain-medium wear over lamp/diode hours.
- Inspect the affected subsystem against the manufacturer's inspection checklist.
- If the fault is confirmed and not a field adjustment, service or replace the laser diode / flashlamp module per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Symptom: Cooling system fault
- Confirm the presentation - typically overheat shutdown mid-treatment, error code on startup.
- Check the most likely cause first: coolant pump, TEC element, or filter degradation.
- Inspect the affected subsystem against the manufacturer's inspection checklist.
- If the fault is confirmed and not a field adjustment, service or replace the cooling system (pump / TEC / filter) per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Operating rooms and surgical procedure suites
- Dermatology and medical-aesthetic clinics
- ENT, gynecology, and specialty procedure rooms
- Outpatient surgical centers
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio →