Lexion Medical Insuflow
Lexion Medical · Model Insuflow
• Less post-operative pain • Reduced hypothermia • Less damage to tissues leading to decreased inflammatory response • Shorter recovery time • Improved outcomes • Improved visualization
Key tips
- ·Never defeat or bypass a return-electrode monitoring (REM) alarm to finish a case - it's a direct burn risk.
- ·Verify OR table battery backup - a table that loses power mid-procedure is a real, documented incident type.
- ·Track surgical light lamp-hours rather than waiting for failure - a sudden failure mid-case is avoidable.
Typical Failure Modes
Failure patterns typical of this equipment class - general BMET reference, not verified against this exact unit's own service history unless flagged. Severity is a category-level estimate.
Peristaltic / roller pump wear
HighSymptoms: Inaccurate flow, pressure alarm.
Root cause: Worn pump rollers or tubing raceway.
Pressure / flow sensor drift
MediumSymptoms: Reported joint/uterine pressure inaccurate.
Root cause: Pressure transducer calibration drift.
Inflow / outflow valve fault
MediumSymptoms: Fluid deficit alarm, uneven distension.
Root cause: Worn solenoid valve or occluded line.
Tubing set seating fault
LowSymptoms: Leak, or won't prime.
Root cause: Worn cassette seat or cracked fitting.
Serviceable Parts & Consumables
The parts a BMET typically services on this class of equipment. Service class and relative cost are general engineering estimates for the category, not figures from this unit's documentation. Part numbers appear only when pulled from this unit's own service manual. Always confirm intervals and pricing against the manufacturer.
Pressure / flow sensor
Class Periodic replacementRel. cost $$$R&R Moderate
Inflow / outflow solenoid valve
Class Periodic replacementRel. cost $$R&R Moderate
Disposable tubing / cassette set
Single-use consumable.
Class ConsumableRel. cost $R&R Easy
Peristaltic pump head
Class Periodic replacementRel. cost $$$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Pressure / flow sensor | Periodic replacement | $$$ | Moderate |
| Inflow / outflow solenoid valve | Periodic replacement | $$ | Moderate |
| Disposable tubing / cassette set Single-use consumable. | Consumable | $ | Easy |
| Peristaltic pump head | Periodic replacement | $$$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Pre-case functional check
- ·Electrosurgical return-electrode cable inspection
- ·Table hydraulic / mechanical inspection
- ·Annual electrical safety test and full PM
Troubleshooting Approach
A structured starting point derived from the failure modes above. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Peristaltic / roller pump wear
- Confirm the presentation - typically inaccurate flow, pressure alarm - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: worn pump rollers or tubing raceway.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the peristaltic pump head per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Symptom: Pressure / flow sensor drift
- Confirm the presentation - typically reported joint/uterine pressure inaccurate - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: pressure transducer calibration drift.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the pressure / flow sensor per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Operating rooms
- Procedure rooms
- Interventional suites
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio →