JOINCHAMP Autoclave N
JOINCHAMP · Model Autoclave N
This medical sterilization equipment has an open-type water tank that conforms to European standards and allows daily cleaning. Our steam autoclave works on the basis of internationally advanced steam sterilization techniques, and the disinfection result is very assuring. The LCD windows are designed to reveal pressure, temperature and time of the sterilization process respectively. The operation panel is easy to use, while date, time and other information can be set by the user. The fully automatic pneumatic lock mechanism is a new generation product to work instead of manual type, and the operation is much easier. Due to the preheat button, the temperature inside the sterilization chamber is always maintained at 70°C or so. As a result, less time is needed for the chamber to reach the desired sterilization temperature, thus cutting down cycle time. The stainless steel liner is manufactured through stretch forming. It has a beautiful appearance, while crack and water leakage are both avoided. Our steam autoclave is able to connect with an external water distillation system for the purpose of automatic water fill, and it can be directly connected with drainage pipes as well so as to discharge remaining water automatically. This N-cycle sterilizer is scientifically designed to deliver outstanding performance in an extremely safe way. For the sterilization chamber, air must be removed so as to get better disinfection results. So, if the door is opened during sterilization process, no matter it is intentionally or by mistake, explosion will take place if you are not lucky enough, and this is resulted from the pressure difference. Accordingly, instruments or supplies inside the chamber will be destroyed. Given this, our type N steam autoclave adopts double lock mechanisms, including manual type and pneumatic type, to avoid damages caused by misoperation. On the other hand, the temperature values of steam generator, inner and outer sides of chamber are all monitored to make sure that instruments inside won’t be damaged as a result of high temperature.
Key tips
- ·Biological-indicator verification applies to dental sterilizers exactly the same as hospital CSSD - no exception for smaller units.
- ·"Sounds different" is often the first real report of handpiece bearing wear, not an outright failure - investigate early rather than waiting.
Typical Failure Modes
Failure patterns typical of this equipment class - general BMET reference, not verified against this exact unit's own service history unless flagged. Severity is a category-level estimate.
Handpiece turbine wear
MediumSymptoms: Low RPM, noise, poor cut.
Root cause: Bearing/turbine wear.
Compressor fault
MediumSymptoms: Low air pressure, moisture.
Root cause: Worn compressor / dryer.
Foot control failure
LowSymptoms: No/erratic activation.
Root cause: Fluid ingress / worn switch.
Curing light LED fade
LowSymptoms: Weak cure, low intensity.
Root cause: LED aging.
Serviceable Parts & Consumables
The parts a BMET typically services on this class of equipment. Service class and relative cost are general engineering estimates for the category, not figures from this unit's documentation. Part numbers appear only when pulled from this unit's own service manual. Always confirm intervals and pricing against the manufacturer.
Foot pedal
Class Periodic replacementRel. cost $$R&R Fairly easy
Curing light LED head
Class Periodic replacementRel. cost $$R&R Fairly easy
Handpiece turbine / cartridge
Most-replaced; track autoclave cycles.
Class Frequent wear itemRel. cost $$$R&R Moderate
Air compressor & dryer
Class Periodic replacementRel. cost $$$R&R Difficult
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Foot pedal | Periodic replacement | $$ | Fairly easy |
| Curing light LED head | Periodic replacement | $$ | Fairly easy |
| Handpiece turbine / cartridge Most-replaced; track autoclave cycles. | Frequent wear item | $$$ | Moderate |
| Air compressor & dryer | Periodic replacement | $$$ | Difficult |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily handpiece lubrication and autoclave cycle verification
- ·Compressor moisture-trap draining
- ·Annual full PM
Troubleshooting Approach
A structured starting point derived from the failure modes above. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Handpiece turbine wear
- Confirm the presentation - typically low RPM, noise, poor cut - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: bearing/turbine wear.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the handpiece turbine / cartridge per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Symptom: Compressor fault
- Confirm the presentation - typically low air pressure, moisture - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: worn compressor / dryer.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the air compressor & dryer per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Dental operatory
- Oral surgery suite
- CSSD (dental sterilizers)
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio →