Imex Medical Systems ImexLab 9100
Imex Medical Systems · Model ImexLab 9100
Better Patient Care - Test patients over 65, hypertensives, diabetics, smokers and victims of stroke, TIAs or heart attack when PAD symptoms appear and prevent more serious complications or surgeries. Full Range of Modalities - The systems performs a wide range of noninvasive test including arterial pressure studies, bilateral photoplethysmography (PPG) and bilateral pneumoplethysmography for waveform analysis. Disk Storage: - Store test results on disk until you are ready to print. The system generates full-page, color reports in seconds with CPT and ICD-9 codes if desired.
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Cannot obtain / hold cuff pressures
HighSymptoms: Segmental cuffs will not inflate or hold, pressure leaks off, study will not complete.
Root cause: Worn cuffs / tubing / connectors, an internal pump / valve fault, or a manifold leak.
PPG / Doppler sensor fault
MediumSymptoms: Flat or noisy PPG / PVR waveform, no Doppler signal.
Root cause: Worn PPG probe or Doppler probe, or a probe-cable fault.
Pressure-transducer / calibration drift
MediumSymptoms: Recorded pressures implausible or biased, calibration fails.
Root cause: Transducer drift or a calibration issue.
Software / PC / report fault
MediumSymptoms: Study will not save, calculate ABI, or generate a report.
Root cause: Workstation PC, software, or the interface.
Printer fault
LowSymptoms: No or faint waveform printout.
Root cause: Printer or paper.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Segmental cuffs & tubing set
Class Frequent wear itemRel. cost $$R&R Easy
PPG / Doppler probe & cable
Class Periodic replacementRel. cost $$R&R Fairly easy
Internal pump / valve manifold
Class Major service partRel. cost $$R&R Moderate
Pressure transducer
Class Major service partRel. cost $$R&R Moderate
Workstation PC / printer
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Segmental cuffs & tubing set | Frequent wear item | $$ | Easy |
| PPG / Doppler probe & cable | Periodic replacement | $$ | Fairly easy |
| Internal pump / valve manifold | Major service part | $$ | Moderate |
| Pressure transducer | Major service part | $$ | Moderate |
| Workstation PC / printer | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Cannot hold cuff pressures
- Fit known-good cuffs and tubing.
- Occlude each channel and confirm it holds pressure.
- Check the manifold and quick-connectors for leaks.
- Verify pressures against a calibrated manometer.
- Refer the internal pump / valve manifold if leaks persist.
Symptom: Poor PPG / Doppler signal
- Swap the PPG / Doppler probe and cable.
- Confirm probe placement and skin contact / gel.
- Flex the cable while watching for dropout.
- Verify on a normal limb.
- Replace the probe if a known-good one works.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio