Hologic QDR 1000
Hologic · Model QDR 1000
Produce hip and spine scans in two to three minutes. Easy upgrades among all QDR models. Equipped with an anthropomorphic spine phantom. No external shielding. High patient throughput.
Key tips
- ·Never bypass a radiation interlock to "just get the image" - this is one of the few true zero-tolerance rules in BMET work.
- ·Trend image-quality phantom results over time - drift shows up before an outright failure does.
- ·Portable/mobile units take real physical abuse from transport - check wheel locks and cable strain reliefs more often than fixed units.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
QC / calibration phantom out of tolerance
HighSymptoms: Daily spine / block phantom BMD trends out of control limits, or calibration fails.
Root cause: X-ray source output drift, detector degradation, or a calibration-drum / reference fault.
C-arm / table scanning-drive fault
MediumSymptoms: The scanning arm or table will not move smoothly, position error, scan aborts, image geometry wrong.
Root cause: Drive motor, belt, or an encoder / limit-sensor fault.
X-ray generation fault
MediumSymptoms: Exposure inhibited, kV error, no counts / very noisy scan.
Root cause: X-ray tube / HV supply, or the filter-wheel / calibration-drum.
Detector fault
MediumSymptoms: Missing scan lines, non-uniform image, detector-error message.
Root cause: Detector element / electronics degradation.
Workstation / software fault
LowSymptoms: Analysis software hangs, scans will not archive or transfer.
Root cause: Workstation PC or software fault.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
X-ray tube / HV supply
Class Major service partRel. cost $$$$R&R Expert-level
Detector assembly
Class Major service partRel. cost $$$$R&R Difficult
Scanning-drive motor / belt / encoder
Class Major service partRel. cost $$$R&R Difficult
Calibration drum / filter wheel
Class Major service partRel. cost $$$R&R Difficult
Workstation PC
Class Major service partRel. cost $$$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| X-ray tube / HV supply | Major service part | $$$$ | Expert-level |
| Detector assembly | Major service part | $$$$ | Difficult |
| Scanning-drive motor / belt / encoder | Major service part | $$$ | Difficult |
| Calibration drum / filter wheel | Major service part | $$$ | Difficult |
| Workstation PC | Major service part | $$$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily QC per modality: image-quality phantom test
- ·Tube and detector inspection
- ·Annual state-required radiation safety survey
- ·Vendor-scheduled preventive maintenance
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: QC / calibration phantom out of tolerance
- Repeat the daily phantom scan and apply the shift / drift rules.
- Confirm the phantom is the correct one and correctly positioned.
- Run the system calibration.
- Review the source / detector trend.
- Escalate a confirmed source or detector drift to the OEM; do not scan patients until QC is back in control.
Symptom: Scanning arm / table drive fault / geometry error
- Note the position / geometry error.
- Check for a mechanical obstruction on the arm / table.
- Run the drive self-test / calibration.
- Inspect the drive belt and encoder.
- Replace the drive component or refer as isolated.
Symptom: X-ray generation / detector fault (no counts, noisy scan, missing lines)
- Note the error and whether it is source or detector.
- Check the X-ray tube / HV supply and the filter wheel / calibration drum.
- Run detector diagnostics.
- Escalate a tube or detector fault to the OEM.
- Re-run QC after any correction.
Technical Specs
- Height
- 50 in
- Width
- 72 in
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Radiology / Imaging department
- Emergency Department (portable units)
- Operating Room (C-arms)
- Cath lab
- Bedside ICU (portable X-ray)
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio