Hillrom UniFlex Headwalls
Hillrom · Model UniFlex Headwalls
Uniflex® Headwalls Easy Installation: Delivered pre-plumbed and pre-wired to permit single point connections for each service type. Flexible Design: The headwall comes in variable lengths and a wide choice of laminate colors.
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Medical-gas outlet leak / check-valve wear
HighSymptoms: Hiss at an outlet, low-pressure alarm on bedside equipment.
Root cause: Worn outlet check valve/seal or a loose union in the pre-plumbed manifold.
Electrical receptacle failure
HighSymptoms: Dead or intermittent outlet, breaker trips.
Root cause: Loose pre-wired terminal or worn receptacle.
Access-panel / joint alignment issue
LowSymptoms: Panels bind, gaps at joints between headwall lengths.
Root cause: Frame racking or worn panel hardware.
Nurse-call / low-voltage fault
MediumSymptoms: Nurse-call not registering, dead data jack.
Root cause: Unseated punch-down or damaged cable.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Gas outlet check-valve / seal kit (per gas)
Class Major service partRel. cost $$R&R Moderate
Hospital-grade receptacle
Class Major service partRel. cost $R&R Fairly easy
Access-panel hardware kit
Class Major service partRel. cost $R&R Moderate
Nurse-call / data jack module
Class Major service partRel. cost $R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Gas outlet check-valve / seal kit (per gas) | Major service part | $$ | Moderate |
| Hospital-grade receptacle | Major service part | $ | Fairly easy |
| Access-panel hardware kit | Major service part | $ | Moderate |
| Nurse-call / data jack module | Major service part | $ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Gas outlet leaking
- Take the gas out of use and open the access panel.
- Leak-test the outlet and manifold union.
- Fit the correct gas-specific check-valve kit.
- Pressure- and flow-test to the facility / NFPA 99 spec.
- Confirm gas keying and labelling before closing.
Symptom: Bedside outlet dead
- Check the branch breaker and upstream GFCI.
- De-energise and re-torque the pre-wired terminals.
- Replace the receptacle if worn or heat-marked.
- Run receptacle tension, polarity and ground tests.
- Electrical-safety-test before return to service.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio