Hillrom Excel Care ES
Hillrom · Model Excel Care ES
• Expandable width surface offers side air bolster expansion,with both foam and air surface, from 40 to 50 inches for greater patient comfort and safety • Adjustable length helps keep patients from sliding down in bed • Seat deflate for easier patient egress and ingress–available with low air loss only • Robust, easy-to-grip patient-assist siderails allow patients to reposition themselves more easily • Aesthetic design for patient dignity and satisfaction • Trendelenburg and Reverse Trendelenburg for easier patient positioning
Key tips
- ·Casters and the wheel-lock brake take the most day-to-day wear - check both every PM, not just on complaint.
- ·A cracked weld or loose frame joint is a safety-critical finding - pull the unit from service until it's repaired.
Typical Failure Modes
Failure patterns typical of this equipment class - general BMET reference, not verified against this exact unit's own service history unless flagged. Severity is a category-level estimate.
Brake / wheel-lock failure
HighSymptoms: Won't hold position, rolls when locked.
Root cause: Brake pad wear or linkage failure.
Caster / wheel wear
MediumSymptoms: Hard to push straight, wobbles or drags.
Root cause: Bearing wear or a flat-spotted wheel.
Frame / weld fatigue
HighSymptoms: Visible crack or looseness at a joint.
Root cause: Repeated load cycling.
Upholstery / surface tear
MediumSymptoms: Torn or cracked cover, exposed padding.
Root cause: Cleaning-chemical and UV degradation, routine wear.
Serviceable Parts & Consumables
The parts a BMET typically services on this class of equipment. Service class and relative cost are general engineering estimates for the category, not figures from this unit's documentation. Part numbers appear only when pulled from this unit's own service manual. Always confirm intervals and pricing against the manufacturer.
Frame hardware (bolts, pins, bushings)
Class Major service partRel. cost $R&R Fairly easy
Caster wheel assembly
Class Periodic replacementRel. cost $$R&R Fairly easy
Brake / wheel-lock mechanism
Class Periodic replacementRel. cost $$R&R Fairly easy
Upholstery / seat or surface cover
Consumable - replace on visible wear or tear.
Class Periodic replacementRel. cost $R&R Easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Frame hardware (bolts, pins, bushings) | Major service part | $ | Fairly easy |
| Caster wheel assembly | Periodic replacement | $$ | Fairly easy |
| Brake / wheel-lock mechanism | Periodic replacement | $$ | Fairly easy |
| Upholstery / seat or surface cover Consumable - replace on visible wear or tear. | Periodic replacement | $ | Easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Caster / wheel and brake function check
- ·Frame, weld, and mounting-hardware inspection
- ·Upholstery / surface condition check
- ·Annual full PM
Troubleshooting Approach
A structured starting point derived from the failure modes above. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Caster / wheel wear
- Confirm the presentation - typically hard to push straight, wobbles or drags.
- Check the most likely cause first: bearing wear or a flat-spotted wheel.
- Inspect the affected subsystem against the manufacturer's inspection checklist.
- If the fault is confirmed and not a field adjustment, service or replace the caster wheel assembly per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Symptom: Brake / wheel-lock failure
- Confirm the presentation - typically won't hold position, rolls when locked.
- Check the most likely cause first: brake pad wear or linkage failure.
- Inspect the affected subsystem against the manufacturer's inspection checklist.
- If the fault is confirmed and not a field adjustment, service or replace the brake / wheel-lock mechanism per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Technical Specs
- Height
- 29 in to 17
- Bed Type
- Electric
- Length
- 91 in to 100
- Patient Weight Capacity
- 1000 lbs
- Width
- 43 in to 53
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Ambulance / transport vehicles
- Emergency Department
- Inter-facility transport teams
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio →