i-STAT
ABBOTT POINT OF CARE INC. · Model 03P75-82
I-Stat 1 Wireless Analyzer.
Intended use: A portable, electrically-powered instrument intended to be used by health professionals at the point-of-care for the qualitative and/or quantitative in vitro detection of multiple clinical chemistry analytes in a clinical specimen, using one or more technology(ies) [e.g., microfluidics, electrometry, spectrophotometry, colorimetry, fluorimetry, radiometry, chemiluminescence]. Analytes detected may include electrolytes, specific proteins, clinical chemistry substrates (e.g., lipid profile), liver and/or cardiac function test analytes, and/or enzymes.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Cartridge error / quality-check failure
HighSymptoms: "*** " or a numbered cartridge / QC code, result suppressed, run aborts.
Root cause: Cartridge out of date or stored wrong, air in the sample, an under- or over-filled cartridge, or a cartridge sensor fault.
Analyzer will not read the cartridge / mechanical fault
MediumSymptoms: Cartridge not detected, motor / positioning error, will not draw sample.
Root cause: Contaminated or worn internal conductor pins / cartridge port, or a mechanical drive fault.
Battery fault
MediumSymptoms: Low-battery lockout, will not power on, short life on disposable or rechargeable batteries.
Root cause: Depleted or aged batteries, or a battery-contact fault.
Thermal / temperature check fault
MediumSymptoms: Temperature out-of-range code, analyzer will not run cartridges.
Root cause: Ambient outside the operating range, or the internal thermal probe / heater fault.
Wireless / downloader communication fault
LowSymptoms: Results not transmitting to the data manager, will not sync via the downloader or Wi-Fi.
Root cause: Downloader / cradle, network configuration, or the analyzer radio.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Batteries (disposable lithium or rechargeable pack)
Class Frequent wear itemRel. cost $R&R Easy
Electronic Simulator (QC accessory)
Use to verify the analyzer's cartridge-reading electronics.
Class Major service partRel. cost $$R&R Easy
Downloader / recharger cradle
Class Major service partRel. cost $$R&R Easy
i-STAT cartridges
Single-use; refrigerate and use within the room-temperature window.
Class Frequent wear itemRel. cost $$R&R Easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Batteries (disposable lithium or rechargeable pack) | Frequent wear item | $ | Easy |
| Electronic Simulator (QC accessory) Use to verify the analyzer's cartridge-reading electronics. | Major service part | $$ | Easy |
| Downloader / recharger cradle | Major service part | $$ | Easy |
| i-STAT cartridges Single-use; refrigerate and use within the room-temperature window. | Frequent wear item | $$ | Easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Cartridge / QC error code
- Look the code up in the i-STAT System Manual's Troubleshooting section.
- Confirm the cartridge is in date and was at room temperature for the specified time.
- Fill the cartridge correctly (to the fill mark, no bubbles) and close the snap shut firmly.
- Run the Electronic Simulator to verify the analyzer electronics.
- If the simulator passes but cartridges keep failing, quarantine the cartridge lot; if the simulator fails, refer the analyzer.
Symptom: Analyzer will not read cartridges
- Run the Electronic Simulator.
- Inspect the cartridge port and internal contact pins for contamination.
- Clean per the manual (no fluids into the port).
- Fit fresh batteries.
- If the simulator still fails, replace / refer the analyzer.
Technical Specs
- Handling Environment Temperature
- 16°C to 46°C
- MRI safety
- Labeling does not contain MRI Safety Information
- Sterile
- No
- Single use
- No
- FDA distribution status
- In Commercial Distribution
- Device type (GMDN)
- Multiple clinical chemistry analyser IVD, point-of-care
- FDA product classification
- Glucose Oxidase, Glucose
- Manufacturer support
- +1(800)366-8020 · techsvc@apoc.abbott.com
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio