Shimadzu FluoroSpeed 300/DAR-8000i

Shimadzu logo Shimadzu · Model FluoroSpeed 300/DAR-8000i

Designed with ease of use and maximum throughput in mind. Increased accuracy and speed of patient positioning and therefore decrease the examination time Space-Saving Design Utilizing the latest in system engineering and technology Patient safety rails and hand grips A special Fluoro interlock switch is designed to prevent accidental activation of exposures.

Key tips

·Never bypass a radiation interlock to "just get the image" - this is one of the few true zero-tolerance rules in BMET work.
·Trend image-quality phantom results over time - drift shows up before an outright failure does.
·Portable/mobile units take real physical abuse from transport - check wheel locks and cable strain reliefs more often than fixed units.

Typical Failure Modes

Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.

Fluoro dose-rate / image-brightness fault
High
Symptoms: Fluoro image too dark or bright, dose creep, ABC / ADRC not tracking.
Root cause: Image-intensifier or flat-panel degradation, or the dose-control loop.
No or inconsistent exposure / generator error
High
Symptoms: Exposure inhibited, generator error code, spot images under/over-exposed.
Root cause: HV generator / tank, tube, filament supply, or an interlock.
Table motion / tilt / spot-film device fault
Medium
Symptoms: Table will not tilt or move, the spot-film / carriage will not position.
Root cause: Table drive, tilt motor, or the spot-film device drive.
Tube overload / cooling fault
Medium
Symptoms: Exposures inhibited after a series, tube-heat alarm.
Root cause: Tube heat limit reached or a heat-exchanger / cooling fault.
Console / image-chain / PACS fault
Medium
Symptoms: Console unresponsive, image freeze, images will not archive.
Root cause: Console PC, the image-processing chain, or the network.

Serviceable Parts & Consumables

Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.

X-ray tube assembly

Class Major service partRel. cost $$$$R&R Expert-level

Image intensifier / flat-panel detector

Class Major service partRel. cost $$$$R&R Expert-level

HV generator / tank components

Class Major service partRel. cost $$$$R&R Expert-level

Table / tilt drive components

Class Major service partRel. cost $$$R&R Difficult

Heat exchanger / cooling components

Class Major service partRel. cost $$$R&R Difficult

Part	Service class	Relative cost	R&R difficulty
X-ray tube assembly	Major service part	$$$$	Expert-level
Image intensifier / flat-panel detector	Major service part	$$$$	Expert-level
HV generator / tank components	Major service part	$$$$	Expert-level
Table / tilt drive components	Major service part	$$$	Difficult
Heat exchanger / cooling components	Major service part	$$$	Difficult

Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.

PM Checklist

Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.

·Daily QC per modality: image-quality phantom test
·Tube and detector inspection
·Annual state-required radiation safety survey
·Vendor-scheduled preventive maintenance

Error Codes

Extracted directly from this unit's own service manual.

1Warning in the case of trying to shut down the system before the changes are saved.

2Warning in the case of trying to read other XML file before the changes are saved.

3Warning in the case that the error occurs in XMLDOM.

4Warning in the case that the error occurs during reading XML file.

5Warning in the case that the error occurs during writing XML file.

6Warning in the case that the number of objects exceeds 256.

7Warning in the case that the program error occurs.

8Warning in the case of failing to read the background picture file.

9Warning in the case that the information on XML is not changed.

10Warning when the coordinates value is incorrect.

11Warning in the case of overwriting existing file.

12Warning in the case that "OverlayInfoEdit.init" is not found in the system start.

13Warning in the case of dragging object outside the preview area.

Troubleshooting Approach

A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.

Symptom: Image artefacts / poor fluoro or CT image / failed calibration

Run the daily air / water (fast) calibration; if it fails, run the full calibration set.
Scan / image a uniform phantom and review uniformity and noise against baseline.
Check the X-ray tube warm-up and heat-unit / arc status.
Check the detector / image-intensifier / flat-panel performance via service diagnostics.
Escalate a confirmed detector-channel, DAS or tube fault to the OEM; re-verify with the phantom after any correction.

Symptom: Exposure aborts / tube-arc errors / kV-mAs fault

Record the exact error codes and the phase (warm-up vs scan / fluoro vs cine).
Run extended tube conditioning / seasoning.
Review the arc-count and heat-unit trend.
Confirm the chiller / heat-exchanger operates and coolant is at level.
Plan a tube replacement when arc counts climb or output drifts; verify output after any HV work.

Symptom: Gantry rotation / slip-ring / positioner fault

Note the axis and any collision-sensor indication.
Clear obstructions and check the body-contour / collision sensors.
Inspect the slip-ring brushes (dust, wear) and the drive belt / bearings.
Run the motion self-test / calibration.
Replace the brush set / drive component or refer as isolated.

Symptom: Table / cradle drifts, will not index or reach position

Note the position / geometry error.
Check for a mechanical obstruction on the table.
Run the table drive self-test / calibration.
Inspect the drive, brake and encoder.
Replace the drive component or refer as isolated.

Symptom: Reconstruction / console / PACS fault

Note the console / recon error.
Restart the recon hardware / console per the OEM procedure.
Check free storage and the database.
Confirm the network link to PACS.
Escalate a recon-hardware or host fault to the OEM.

Technical Specs

Motorized Tilting/Pivot Rotation: 90

Typical Location

Where this class of equipment is typically deployed - general reference, not this unit's own placement record.

Radiology / Imaging department
Emergency Department (portable units)
Operating Room (C-arms)
Cath lab
Bedside ICU (portable X-ray)

Documents & Manuals

Safety & Recalls

Synced live from the FDA openFDA API.

RECALL
Eight fixing bolts at the base of the X-ray ceiling tube column assembly may be loose or missing so service is required to install a cable, bracket, and label behind the bracket, indicating when service is required, to eliminate the risk of the device falling.
RECALL
It was found that the irradiated x-ray may exceed the xray radiation dose rate specified in CFR 1020.32 in some specific case of fluoroscopic mode due to inadequate adjusting criteria in installation.
RECALL
The DAP meters were found to be outside of tolerance.
RECALL
Report of unintentional movement of table to reverse tilting.
RECALL
Shimadzu Corporation is recalling the Shimadzu Digital X-Ray System because they have received a report of a lost image under certain circumstances.

Troubleshoot this device with Bio

Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.

Ask Bio

Shimadzu FluoroSpeed 300/DAR-8000i

Shimadzu logo Shimadzu · Model FluoroSpeed 300/DAR-8000i

Key tips

·Never bypass a radiation interlock to "just get the image" - this is one of the few true zero-tolerance rules in BMET work.
·Trend image-quality phantom results over time - drift shows up before an outright failure does.
·Portable/mobile units take real physical abuse from transport - check wheel locks and cable strain reliefs more often than fixed units.

Typical Failure Modes

Fluoro dose-rate / image-brightness fault
High
Symptoms: Fluoro image too dark or bright, dose creep, ABC / ADRC not tracking.
Root cause: Image-intensifier or flat-panel degradation, or the dose-control loop.
No or inconsistent exposure / generator error
High
Symptoms: Exposure inhibited, generator error code, spot images under/over-exposed.
Root cause: HV generator / tank, tube, filament supply, or an interlock.
Table motion / tilt / spot-film device fault
Medium
Symptoms: Table will not tilt or move, the spot-film / carriage will not position.
Root cause: Table drive, tilt motor, or the spot-film device drive.
Tube overload / cooling fault
Medium
Symptoms: Exposures inhibited after a series, tube-heat alarm.
Root cause: Tube heat limit reached or a heat-exchanger / cooling fault.
Console / image-chain / PACS fault
Medium
Symptoms: Console unresponsive, image freeze, images will not archive.
Root cause: Console PC, the image-processing chain, or the network.

Serviceable Parts & Consumables

X-ray tube assembly

Class Major service partRel. cost $$$$R&R Expert-level

Image intensifier / flat-panel detector

Class Major service partRel. cost $$$$R&R Expert-level

HV generator / tank components

Class Major service partRel. cost $$$$R&R Expert-level

Table / tilt drive components

Class Major service partRel. cost $$$R&R Difficult

Heat exchanger / cooling components

Class Major service partRel. cost $$$R&R Difficult

Part	Service class	Relative cost	R&R difficulty
X-ray tube assembly	Major service part	$$$$	Expert-level
Image intensifier / flat-panel detector	Major service part	$$$$	Expert-level
HV generator / tank components	Major service part	$$$$	Expert-level
Table / tilt drive components	Major service part	$$$	Difficult
Heat exchanger / cooling components	Major service part	$$$	Difficult

Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.

PM Checklist

Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.

·Daily QC per modality: image-quality phantom test
·Tube and detector inspection
·Annual state-required radiation safety survey
·Vendor-scheduled preventive maintenance

Error Codes

Extracted directly from this unit's own service manual.

1Warning in the case of trying to shut down the system before the changes are saved.

2Warning in the case of trying to read other XML file before the changes are saved.

3Warning in the case that the error occurs in XMLDOM.

4Warning in the case that the error occurs during reading XML file.

5Warning in the case that the error occurs during writing XML file.

6Warning in the case that the number of objects exceeds 256.

7Warning in the case that the program error occurs.

8Warning in the case of failing to read the background picture file.

9Warning in the case that the information on XML is not changed.

10Warning when the coordinates value is incorrect.

11Warning in the case of overwriting existing file.

12Warning in the case that "OverlayInfoEdit.init" is not found in the system start.

13Warning in the case of dragging object outside the preview area.

Troubleshooting Approach

A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.

Symptom: Image artefacts / poor fluoro or CT image / failed calibration

Run the daily air / water (fast) calibration; if it fails, run the full calibration set.
Scan / image a uniform phantom and review uniformity and noise against baseline.
Check the X-ray tube warm-up and heat-unit / arc status.
Check the detector / image-intensifier / flat-panel performance via service diagnostics.
Escalate a confirmed detector-channel, DAS or tube fault to the OEM; re-verify with the phantom after any correction.

Symptom: Exposure aborts / tube-arc errors / kV-mAs fault

Record the exact error codes and the phase (warm-up vs scan / fluoro vs cine).
Run extended tube conditioning / seasoning.
Review the arc-count and heat-unit trend.
Confirm the chiller / heat-exchanger operates and coolant is at level.
Plan a tube replacement when arc counts climb or output drifts; verify output after any HV work.

Symptom: Gantry rotation / slip-ring / positioner fault

Note the axis and any collision-sensor indication.
Clear obstructions and check the body-contour / collision sensors.
Inspect the slip-ring brushes (dust, wear) and the drive belt / bearings.
Run the motion self-test / calibration.
Replace the brush set / drive component or refer as isolated.

Symptom: Table / cradle drifts, will not index or reach position

Note the position / geometry error.
Check for a mechanical obstruction on the table.
Run the table drive self-test / calibration.
Inspect the drive, brake and encoder.
Replace the drive component or refer as isolated.

Symptom: Reconstruction / console / PACS fault

Note the console / recon error.
Restart the recon hardware / console per the OEM procedure.
Check free storage and the database.
Confirm the network link to PACS.
Escalate a recon-hardware or host fault to the OEM.

Technical Specs

Motorized Tilting/Pivot Rotation: 90

Typical Location

Where this class of equipment is typically deployed - general reference, not this unit's own placement record.

Radiology / Imaging department
Emergency Department (portable units)
Operating Room (C-arms)
Cath lab
Bedside ICU (portable X-ray)

Documents & Manuals

Safety & Recalls

Synced live from the FDA openFDA API.

RECALL
Eight fixing bolts at the base of the X-ray ceiling tube column assembly may be loose or missing so service is required to install a cable, bracket, and label behind the bracket, indicating when service is required, to eliminate the risk of the device falling.
RECALL
It was found that the irradiated x-ray may exceed the xray radiation dose rate specified in CFR 1020.32 in some specific case of fluoroscopic mode due to inadequate adjusting criteria in installation.
RECALL
The DAP meters were found to be outside of tolerance.
RECALL
Report of unintentional movement of table to reverse tilting.
RECALL
Shimadzu Corporation is recalling the Shimadzu Digital X-Ray System because they have received a report of a lost image under certain circumstances.

Troubleshoot this device with Bio

Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.

Ask Bio

Shimadzu FluoroSpeed 300/DAR-8000i

Key tips

Typical Failure Modes

Fluoro dose-rate / image-brightness fault

No or inconsistent exposure / generator error

Table motion / tilt / spot-film device fault

Tube overload / cooling fault

Console / image-chain / PACS fault

Serviceable Parts & Consumables

PM Checklist

Error Codes

Troubleshooting Approach

Symptom: Image artefacts / poor fluoro or CT image / failed calibration

Symptom: Exposure aborts / tube-arc errors / kV-mAs fault

Symptom: Gantry rotation / slip-ring / positioner fault

Symptom: Table / cradle drifts, will not index or reach position

Symptom: Reconstruction / console / PACS fault

Technical Specs

Typical Location

Documents & Manuals

Safety & Recalls

Troubleshoot this device with Bio

Shimadzu FluoroSpeed 300/DAR-8000i

Key tips

Typical Failure Modes

Fluoro dose-rate / image-brightness fault

No or inconsistent exposure / generator error

Table motion / tilt / spot-film device fault

Tube overload / cooling fault

Console / image-chain / PACS fault

Serviceable Parts & Consumables

PM Checklist

Error Codes

Troubleshooting Approach

Symptom: Image artefacts / poor fluoro or CT image / failed calibration

Symptom: Exposure aborts / tube-arc errors / kV-mAs fault

Symptom: Gantry rotation / slip-ring / positioner fault

Symptom: Table / cradle drifts, will not index or reach position

Symptom: Reconstruction / console / PACS fault

Technical Specs

Typical Location

Documents & Manuals

Safety & Recalls

Troubleshoot this device with Bio