Pedigo P-2110
Pedigo · Model P-2110
• All Pedigo fluid warmers are FDA approved. • UL & CSA approved. • 125 VAC. • Designed specifically for the warming of irrigation and intravenous fluids. (NOTE: Use of other types of fluids is not covered under our FDA approval). • Individual temperature controls for irrigation fluids and intravenous fluids allow for precise temperature settings for the proper type of fluid. • Irrigation temperature can be adjusted from 90 to 150 oF (32 to 66 oC) while the intravenous temperature range is 90 to 110 oF (32 to 43 oC). P-2145 low temp is 95oF. • The 4-digit LED display can be set to operate in Fahrenheit or Celsius. • Safety alarm warns if temperatures exceed 10 oF (6 oC) over the set-point temperature. • Built-in lock-out prevents inadvertent altering of temperature setting. • Glass window doors and interior lighting for easy visualization of contents. • Stainless steel construction with a full-perimeter stainless steel bumper. • 5" diameter, heavy-duty casters for ease of mobility, two with locking brakes. P-2110 has rubber feet for countertop use.
Key tips
- ·Never skip temperature-accuracy verification to save time - it's the one check that directly prevents burns.
- ·Hose/blanket connector wear is the most common real fault and the easiest to miss on a quick visual check.
Typical Failure Modes
Failure patterns typical of this equipment class - general BMET reference, not verified against this exact unit's own service history unless flagged. Severity is a category-level estimate.
Heater / element fault
MediumSymptoms: No heat, overheat alarm.
Root cause: Element or thermal fuse failure.
Temperature sensor drift
MediumSymptoms: Setpoint error, alarm.
Root cause: Sensor aging.
Fan / airflow failure
LowSymptoms: Uneven warming, hotspot.
Root cause: Blower wear.
Serviceable Parts & Consumables
The parts a BMET typically services on this class of equipment. Service class and relative cost are general engineering estimates for the category, not figures from this unit's documentation. Part numbers appear only when pulled from this unit's own service manual. Always confirm intervals and pricing against the manufacturer.
Temperature probe
Consumable per patient.
Class Periodic replacementRel. cost $R&R Easy
Heating element / thermal fuse
Common R&R.
Class Periodic replacementRel. cost $$$R&R Moderate
Blower fan
Class Periodic replacementRel. cost $$R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Temperature probe Consumable per patient. | Periodic replacement | $ | Easy |
| Heating element / thermal fuse Common R&R. | Periodic replacement | $$$ | Moderate |
| Blower fan | Periodic replacement | $$ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Hose / blanket connector inspection
- ·Temperature-accuracy verification
- ·Annual electrical safety test
Troubleshooting Approach
A structured starting point derived from the failure modes above. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Heater / element fault
- Confirm the presentation - typically no heat, overheat alarm - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: element or thermal fuse failure.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the heating element / thermal fuse per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Symptom: Fan / airflow failure
- Confirm the presentation - typically uneven warming, hotspot - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: blower wear.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the blower fan per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Operating Room
- PACU
- Emergency Department
- Labor & Delivery
- NICU
Documents & Manuals
No documents available for this device yet.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio →