Olympus Gyrus ACMI CyberWand
Olympus · Model Gyrus ACMI CyberWand
Concentric dual-probe design. Designed for durability. Has a shortened reprocessing cycle of only four minutes.
Key tips
- ·When no category-specific guidance fits, default to the manufacturer's own service manual and the general troubleshooting method in the Engineer's Guide.
- ·Run an incoming and annual electrical safety test regardless of how niche the device is.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Power indicator LED not illuminated
HighSymptoms: Generator dead, no power LED.
Root cause: Power cord not seated at the receptacle or generator, power switch off, or a blown fuse.
Fault indicator illuminated
MediumSymptoms: Fault light on, no lithotripsy output.
Root cause: Footswitch or transducer not plugged into the generator.
Poor performance / low power
MediumSymptoms: Weak or no fragmentation, probe not coupling.
Root cause: Mis-tuned or loose probe - retighten and re-tune the system.
Probe / transducer wear
MediumSymptoms: Cracked probe threads, reduced output, transducer noise.
Root cause: Worn dual-probe set or transducer element.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Generator fuse
Class Major service partRel. cost $R&R Fairly easy
Dual-probe set (floating / fixed probe, spring, mass ring)
Class Frequent wear itemRel. cost $$R&R Fairly easy
Transducer / handpiece
Class Periodic replacementRel. cost $$$R&R Moderate
Footswitch
Class Periodic replacementRel. cost $$R&R Fairly easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Generator fuse | Major service part | $ | Fairly easy |
| Dual-probe set (floating / fixed probe, spring, mass ring) | Frequent wear item | $$ | Fairly easy |
| Transducer / handpiece | Periodic replacement | $$$ | Moderate |
| Footswitch | Periodic replacement | $$ | Fairly easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Follow the manufacturer's PM schedule
- ·Perform incoming and annual electrical safety testing per facility biomedical program
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: No power LED
- With the power switch OFF, seat the power cord at both the wall receptacle and the generator.
- Turn the switch ON.
- If still dead, replace the fuse per the Fuse Replacement section (power cord disconnected).
- Confirm the power LED illuminates.
- Run a function check.
Symptom: Low or no output
- With power OFF, confirm the footswitch and transducer are plugged into the generator.
- Check the probe assembly order (floating probe, return spring, fixed probe, free mass ring).
- Finger-tighten then wrench-tighten the fixed probe to the transducer.
- Re-tune the system.
- Verify output on a test.
Technical Specs
- Length
- 17 cm Transducer Length
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Varies by device - check the unit's own manual for facility placement guidance
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio