Monitor Instruments MI-5000B
Monitor Instruments · Model MI-5000B
• Built in talk over with automatic pause while in use • 2 in 1 serial port configuration (pin-out compatible with older versions) • Excellent immunity to low line voltages • Rugged construction • Allows for field calibration of output levels • Three frequency threshold averaging on printouts • Capability for switching from automatic to manual as needed • Option to start either ear, and whether to test 8 kHz. • Starting ear, whether to test 8 kHz and other audiometer parameters can be stored in non-volatile memory • 'Listening' test controlled by the patient response switch from inside the booth • Optional automatic shut off after one hour when not in use (selection stored in non-volatile memory) • Elapsed test time printed on test results • Flags on printout show which thresholds were determined manually • Audible alert for end of test and error conditions (toggled active or inactive from front panel)
Key tips
- ·Electrode impedance drives data quality more than almost any other single factor - check it before assuming an amplifier fault.
- ·Pre-case verification of intraoperative monitoring equipment isn't optional - a mid-case failure has direct surgical-decision consequences.
Typical Failure Modes
Failure patterns typical of this equipment class - general BMET reference, not verified against this exact unit's own service history unless flagged. Severity is a category-level estimate.
Electrode impedance high
MediumSymptoms: Noisy / flat channels, impedance alarm.
Root cause: Dry gel, poor contact.
Amplifier channel fault
MediumSymptoms: Dead channel, artifact.
Root cause: Front-end amplifier failure.
Stimulator output fault
MediumSymptoms: No stimulus delivered.
Root cause: Stimulator circuit wear.
Grounding / isolation issue
LowSymptoms: 50/60 Hz interference.
Root cause: Shield/ground break.
Serviceable Parts & Consumables
The parts a BMET typically services on this class of equipment. Service class and relative cost are general engineering estimates for the category, not figures from this unit's documentation. Part numbers appear only when pulled from this unit's own service manual. Always confirm intervals and pricing against the manufacturer.
Amplifier channel module
Class Periodic replacementRel. cost $$$R&R Difficult
Stimulator cable
Class Periodic replacementRel. cost $$R&R Fairly easy
EEG electrode cap / cup
Frequent R&R.
Class Periodic replacementRel. cost $$R&R Easy
Patient electrode gel
Consumable.
Class ConsumableRel. cost $R&R Easy
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Amplifier channel module | Periodic replacement | $$$ | Difficult |
| Stimulator cable | Periodic replacement | $$ | Fairly easy |
| EEG electrode cap / cup Frequent R&R. | Periodic replacement | $$ | Easy |
| Patient electrode gel Consumable. | Consumable | $ | Easy |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Electrode / lead impedance check
- ·Amplifier calibration
- ·Annual electrical safety test
Troubleshooting Approach
A structured starting point derived from the failure modes above. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Electrode impedance high
- Confirm the presentation - typically noisy / flat channels, impedance alarm - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: dry gel, poor contact.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the eEG electrode cap / cup per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Symptom: Amplifier channel fault
- Confirm the presentation - typically dead channel, artifact - and note the exact alarm or message and the conditions when it occurs.
- Check the most likely cause first: front-end amplifier failure.
- Isolate the affected subsystem using the manufacturer's functional check or self-test, where one is provided.
- If the fault is confirmed and not a field adjustment, service or replace the patient electrode gel per the manufacturer's service documentation.
- Return the device to service only after the manufacturer's functional and applicable electrical-safety checks pass.
- Record the findings, any parts used, and the verification results in the maintenance history.
Technical Specs
- Height
- 2.75 in
- Length
- 9 in
- Weight
- 2.6 lbs
- Width
- 7.5 in
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Neurology / EEG lab
- ICU (continuous EEG monitoring)
- Operating Room (intraoperative monitoring)
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio →