Konica Minolta Regius RC-110
Konica Minolta · Model Regius RC-110
Easy operation with the simple installation of an exposed cassette. The height of the cassette slot is 710 mm. Delivers processing performance of 76 sheets/hour, achieving a high-speed processing cycle of 47 seconds/plate. The two way setting method allows selection of two patterns of layout depending on the facilities space limitations.
Key tips
- ·Never bypass a radiation interlock to "just get the image" - this is one of the few true zero-tolerance rules in BMET work.
- ·Trend image-quality phantom results over time - drift shows up before an outright failure does.
- ·Portable/mobile units take real physical abuse from transport - check wheel locks and cable strain reliefs more often than fixed units.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Poor image quality / artefacts
HighSymptoms: Banding, streaks, ghost images, non-uniform density, dust artefacts.
Root cause: Dirty light guide / scanning optics, a worn erase-lamp array, imaging-plate wear, or contaminated transport rollers.
Plate / cassette transport jam or mis-feed
MediumSymptoms: Plate jams in the reader, transport error, plate not returned.
Root cause: Worn or contaminated transport rollers / belts, or a sensor fault.
Incomplete erase / residual latent image
MediumSymptoms: A faint previous image appears on the next exposure.
Root cause: Erase-lamp array degradation or a driver fault.
Laser / PMT scanning fault
MediumSymptoms: No or very noisy image, scan-error message.
Root cause: Scanning laser or the photomultiplier / detection chain.
Workstation / DICOM fault
LowSymptoms: Images will not display, annotate or send to PACS.
Root cause: Workstation PC or the DICOM configuration.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Transport rollers / belts
Class Periodic replacementRel. cost $$R&R Moderate
Erase-lamp array
Class Periodic replacementRel. cost $$$R&R Moderate
Imaging plates / cassettes
Class Periodic replacementRel. cost $$$R&R Easy
Light guide / scanning optics
Class Major service partRel. cost $$$R&R Difficult
Workstation PC
Class Major service partRel. cost $$$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Transport rollers / belts | Periodic replacement | $$ | Moderate |
| Erase-lamp array | Periodic replacement | $$$ | Moderate |
| Imaging plates / cassettes | Periodic replacement | $$$ | Easy |
| Light guide / scanning optics | Major service part | $$$ | Difficult |
| Workstation PC | Major service part | $$$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily QC per modality: image-quality phantom test
- ·Tube and detector inspection
- ·Annual state-required radiation safety survey
- ·Vendor-scheduled preventive maintenance
Error Codes
Extracted directly from this unit's own service manual.
06000Justifier HP sensor error (when moving to HP)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06001Justifier motor control error (when moving to HP)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06002Justifier HP sensor error (when moving to cassette fixing position)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06003Justifier motor control error (when moving to cassette fixing position)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06004Justifier motor control error (when moving to minute opening position)
06005Justifier motor control error (when moving to cassette fixing position 2)
06006Justifier HP sensor error (when moving to HP 2)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06007Justifier motor control error (when moving to HP 2)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06008Justifier HP sensor error (when moving to HP 3)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06009Justifier motor control error (when moving to HP 3)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06010Justifier HP sensor error (when moving to minute opening position)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06011Justifier motor control error (when moving to minute opening position 2)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06015Justifier HP sensor error (when moving to HP)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06016Justifier motor control error (when moving to HP)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06017Justifier HP sensor error (when moving to cassette fixing position)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06018Justifier motor control error (when moving to cassette fixing position)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06019Justifier motor control error (when moving to minute opening position)
06020Justifier motor control error (when moving to cassette fixing position 2)
06021Justifier HP sensor error (when moving to HP 2)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06022Justifier motor control error (when moving to HP 2)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06023Justifier HP sensor error (when moving to HP 3)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06024Justifier motor control error (when moving to HP 3)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06025Justifier HP sensor error (when moving to minute opening position)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06026Justifier motor control error (when moving to minute opening position 2)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06030Justifier HP sensor error (when moving to HP)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06031Justifier motor control error (when moving to HP)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06032Justifier HP sensor error (when moving to cassette fixing position)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06033Justifier motor control error (when moving to cassette fixing position)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06034Justifier motor control error (when moving to minute opening position)
06035Justifier motor control error (when moving to cassette fixing position 2)
06036Justifier HP sensor error (when moving to HP 2)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06037Justifier motor control error (when moving to HP 2)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06038Justifier HP sensor error (when moving to HP 3)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06039Justifier motor control error (when moving to HP 3)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06040Justifier HP sensor error (when moving to minute opening position)
Confirm following and replace the faulty parts. • Justifier HP sensor • Sensor wire: JP41 ~ MCN3 (MDU) • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06041Justifier motor control error (when moving to minute opening position 2)
Confirm following and replace the faulty parts. • Justifier motor • Motor wire: JJ50 ~ MCN5 (MDU) • MDU
06050Receiver HP sensor error (when moving to HP)
Confirm following and replace the faulty parts. • Receiver HP sensor • Sensor wire: JP43 ~ MCN3 (MDU) • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06051Receiver motor control error (when moving to HP)
Confirm following and replace the faulty parts. • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06052Receiver HP sensor error (when moving to first falling position)
Confirm following and replace the faulty parts. • Receiver HP sensor • Sensor wire: JP43 ~ MCN3 (MDU) • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06053Receiver motor control error (when moving to first falling position)
Confirm following and replace the faulty parts. • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06054Receiver motor control error (when moving to second falling position)
Confirm following and replace the faulty parts. • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06055Receiver motor control error (when moving slightly down at the second falling position)
Confirm following and replace the faulty parts. • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06056Receiver motor control error (when moving to first falling position 2)
Confirm following and replace the faulty parts. • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06057Receiver HP sensor error (when moving to HP 2)
Confirm following and replace the faulty parts. • Receiver HP sensor • Sensor wire: JP43 ~ MCN3 (MDU) • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06058Receiver motor control error (when moving to HP 2)
Confirm following and replace the faulty parts. • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06059Receiver HP sensor error (when moving to HP 3)
Confirm following and replace the faulty parts. • Receiver HP sensor • Sensor wire: JP43 ~ MCN3 (MDU) • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06060Receiver motor control error (when moving to HP 3)
Confirm following and replace the faulty parts. • Receiver motor • Motor wire: JP51 ~ MCN5 (MDU) • MDU
06061Receiver HP sensor error (when moving to second falling position)
Confirm following and replace the faulty parts. • Receiver HP sensor • Sensor wire: JP43 ~ MCN3 (MDU) • Receiver motor • Motor wire: JJ51 ~ MCN5 (MDU) • MDU
06062Receiver motor control error (when moving to second falling position 2)
Confirm following and replace the faulty parts. • Receiver motor • Motor wire: JJ51 ~ MCN5 (MDU) • MDU
06100Transporter read sensor error (when moving to read position)
1. Confirm that there are no foreign objects between the push plate and the frame, and remove if there are any. 2. Confirm if there is enough grease on the drive shaft, nut, or transporter motor unit, and apply grease if it is not enough. 3. Confirm following and replace the faulty parts. • Tumbler (if the spring is not broken) • Transporter read sensor • Sensor wire: JP47 ~ MCN4 (MDU) • Transporter motor • Motor wire: JP52 ~ MCN6 (MDU) • MDU
06101Transporter motor control error (when moving to read position)
1. Confirm the ground. (It may cause noise) 2. Confirm that the antistatic brush right under the insertion slot has not fallen off. 3. Confirm following and replace the faulty parts. • Ground wire of transporter unit (if it is not broken) • Transporter motor • Motor wire: JP52 ~
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Poor image quality / artefacts (banding, streaks, ghosting, non-uniform density)
- Run the reader's cleaning and calibration / shading procedure.
- Clean the light guide, scanning optics and the transport rollers.
- Erase and re-image a plate to check for a residual latent image (worn erase lamps).
- Rotate in a fresh imaging plate / cassette to rule out plate wear.
- Escalate a scanning-laser / PMT / detector fault to the OEM.
Symptom: Plate / cassette jams or is not returned
- Clear the jammed plate per the manual and note where it hangs up.
- Inspect and clean or replace the transport rollers and belts.
- Check the transport / position sensors.
- Cycle several cassettes.
- Confirm reliable feed and return.
Symptom: Faint previous image on the next exposure (incomplete erase)
- Check the erase-lamp array for failed lamps / segments.
- Run an extended erase and re-image.
- Check the erase-lamp driver.
- Replace the erase-lamp array.
- Confirm a clean plate after a full erase.
Symptom: Images will not display, process or reach PACS
- Confirm the workstation is up and the DICOM store settings are correct.
- Send a test image and read the error.
- Check free disk space and the database.
- Restart the acquisition service.
- Escalate a workstation / network fault to IT.
Technical Specs
- Height
- 747
- Length
- 365
- Weight
- 106 kg
- Width
- 740
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Radiology / Imaging department
- Emergency Department (portable units)
- Operating Room (C-arms)
- Cath lab
- Bedside ICU (portable X-ray)
Documents & Manuals
Safety & Recalls
Synced live from the FDA openFDA API.
- RECALL
A hand grip column, even though locked in position, moved downward about 3 cm while a patient was holding the hand grip for lateral exposure. When the hand grip moved down, the patient who was holding it lost his or her balance and almost fell. This problem only occurred in Japan with one system.
- RECALL
If the patient demographic data is entered into the CS-1 manually, and the user fails to enter any data in one of the demographic data fields labeled as Birthday, Sex, Name or Patient Comments, etc, the RIM will populate the fields where no data has been entered with data from the previous patient.
- RECALL
One feature of the software on some of the devices which permits assembling three digital images into one image has occasionally had problems aligning the three images exactly.
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio