InnoVet Versa DR
InnoVet · Model Versa DR
Superior image quality with the lowest patient dosage. Lowest overall cost of ownership. Our most compact and powerful digital offering to date 20% smaller footprint. User-friendly DICOM compliant imaging software integrates seamlessly with most practice management software.
Key tips
- ·Never bypass a radiation interlock to "just get the image" - this is one of the few true zero-tolerance rules in BMET work.
- ·Trend image-quality phantom results over time - drift shows up before an outright failure does.
- ·Portable/mobile units take real physical abuse from transport - check wheel locks and cable strain reliefs more often than fixed units.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Fails the pre-use leak check
HighSymptoms: Breathing-circuit / absorber leak test fails, machine not ready for use.
Root cause: Breathing-circuit / absorber leak, a worn APL valve or bag arm, or a CO2-absorber canister seal.
O2 flowmeter / delivery fault
MediumSymptoms: O2 flow not matching the setting, flowmeter float sticking, no O2 flush.
Root cause: Worn flowmeter (rotameter) or a flush-valve fault.
Vaporiser fault
MediumSymptoms: Agent not vaporising correctly, output does not match the dial, back-bar leak.
Root cause: Vaporiser seating / O-ring, or an internal vaporiser fault.
Ventilator / bellows fault (Versa)
MediumSymptoms: Set tidal volume not delivered, bellows will not fill, PEEP not held.
Root cause: Bellows leak, drive-gas valve, or a flow-sensor fault.
Scavenging (WAGD) fault
LowSymptoms: Waste-gas scavenging alarm or not evacuating.
Root cause: Scavenging flow / connection or a receiver-valve fault.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
APL valve / breathing-circuit gaskets
Class Periodic replacementRel. cost $$R&R Fairly easy
CO2 absorbent / canister seals
Class ConsumableRel. cost $R&R Easy
O2 flowmeter (rotameter)
Class Major service partRel. cost $$R&R Moderate
Vaporiser O-ring / back-bar seal
Class Periodic replacementRel. cost $R&R Fairly easy
Ventilator bellows (Versa)
Class Major service partRel. cost $$$R&R Difficult
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| APL valve / breathing-circuit gaskets | Periodic replacement | $$ | Fairly easy |
| CO2 absorbent / canister seals | Consumable | $ | Easy |
| O2 flowmeter (rotameter) | Major service part | $$ | Moderate |
| Vaporiser O-ring / back-bar seal | Periodic replacement | $ | Fairly easy |
| Ventilator bellows (Versa) | Major service part | $$$ | Difficult |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Daily QC per modality: image-quality phantom test
- ·Tube and detector inspection
- ·Annual state-required radiation safety survey
- ·Vendor-scheduled preventive maintenance
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Leak check fails
- Run the leak test with the exact circuit and absorber.
- Reseat the CO2-absorber canister and check its seal; replace exhausted absorbent.
- Inspect the breathing-circuit gaskets, bag arm and APL valve.
- Check the vaporiser is seated with an intact O-ring.
- Re-run the test.
Symptom: O2 flow / vaporiser fault
- Verify O2 flow with a calibrated flow meter.
- Tap the flowmeter to free a stuck float; replace the rotameter if it sticks.
- Check the vaporiser output against the dial with an agent analyser if available.
- Replace the vaporiser O-ring / back-bar seal.
- Refer the vaporiser for service if output is still wrong.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Radiology / Imaging department
- Emergency Department (portable units)
- Operating Room (C-arms)
- Cath lab
- Bedside ICU (portable X-ray)
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio