Blickman 7925TS
Blickman · Model 7925TS
Quality and control features are the same as those on the larger models. An adjustable shelf comes standard. Suggested that these units sit on an existing cabinet, or on a Blickman transport dolly or mobile stand. Easy-to-use keypad with controls for setting internal temperature is conveniently located above door. Available with glass or stainless-steel door. Options include: sloping tops; mobile stand for table-top models; pass-thru capability.
Key tips
- ·Never skip temperature-accuracy verification to save time - it's the one check that directly prevents burns.
- ·Hose/blanket connector wear is the most common real fault and the easiest to miss on a quick visual check.
Typical Failure Modes
Compiled for this model from its own documentation and established engineering knowledge for this equipment class - not from a verified service record. Confirm against the manufacturer's service manual.
Cabinet not reaching / holding set temperature
HighSymptoms: Blanket / fluid cabinet below (or above) setpoint, temperature alarm.
Root cause: Heater element, a temperature sensor / controller fault, a door / gasket leak, or a circulation-fan fault.
Over-temperature safety trip
MediumSymptoms: Cabinet stops heating, over-temp alarm, will not restart.
Root cause: Controller / sensor fault driving the heater high, or a failed independent over-temp thermostat.
Door / gasket / hinge fault
MediumSymptoms: Door will not seal, heat loss, temperature swings when opened.
Root cause: Worn door gasket or a sagging hinge.
Circulation-fan fault
MediumSymptoms: Uneven temperature top to bottom, fan noise or stopped.
Root cause: Worn circulation fan.
Display / controller fault
LowSymptoms: Blank or frozen display, setpoint will not change.
Root cause: Controller or display fault.
Serviceable Parts & Consumables
Serviceable items for this model, compiled from its documentation and engineering knowledge for this equipment class. Service class and relative cost are estimates, not manufacturer figures; no part numbers are given. Confirm intervals and pricing against the manufacturer.
Heater element
Class Major service partRel. cost $$R&R Difficult
Temperature sensor / over-temp thermostat
Class Major service partRel. cost $$R&R Moderate
Door gasket
Class Periodic replacementRel. cost $$R&R Fairly easy
Circulation fan
Class Major service partRel. cost $$R&R Moderate
Controller / display
Class Major service partRel. cost $$R&R Moderate
| Part | Service class | Relative cost | R&R difficulty |
|---|---|---|---|
| Heater element | Major service part | $$ | Difficult |
| Temperature sensor / over-temp thermostat | Major service part | $$ | Moderate |
| Door gasket | Periodic replacement | $$ | Fairly easy |
| Circulation fan | Major service part | $$ | Moderate |
| Controller / display | Major service part | $$ | Moderate |
Relative cost: $ lowest · $$$$ highest service-part cost for this equipment class. Not a price.
PM Checklist
Preventive-maintenance tasks typical of this equipment class. Perform to the manufacturer's procedure and your facility's policy - this is general reference, not a schedule for this specific unit.
- ·Hose / blanket connector inspection
- ·Temperature-accuracy verification
- ·Annual electrical safety test
Error Codes
Extracted directly from this unit's own service manual.
Er 1Reversed Thermo-couple connection +/-.
Er 2Sensor type mismatchor open RTD.
Er 3Sensor type mismatch.
Er 4Open thermocouple, bad connection, broken wire.
Er 5Electrical noise.
BlankControl is inoperable.
HI (with Audible)Cabinet temp is 10 degrees higher than setting.
LLLLInput temperature is lower than input range.
HHHHInput temperature is higher than input range.
OPEnInput sensor is not connected.
JIC (Continuously)Controller failure
Troubleshooting Approach
A starting sequence for this model, compiled from its documentation and engineering knowledge for this equipment class. Follow the manufacturer's service documentation for the actual procedure.
Symptom: Cabinet not reaching / holding the set temperature
- Compare the cabinet temperature to an independent calibrated thermometer at several shelf positions.
- Confirm the door seals and the gasket is intact.
- Check the circulation fan runs.
- Verify the heater element draws current.
- Replace the sensor, controller or heater as isolated; confirm the maximum blanket / fluid temperature complies with policy.
Symptom: Over-temperature safety trip / will not restart
- Let the cabinet cool.
- Compare the display to an independent reference.
- Replace the temperature sensor if it disagrees.
- Check the independent over-temperature thermostat.
- Confirm stable control before returning to use.
Symptom: Door will not seal / temperature swings when opened
- Inspect the door gasket and hinge.
- Adjust the door / latch.
- Replace a worn gasket.
- Confirm recovery time after a door opening.
- Check the circulation fan distributes heat evenly.
Typical Location
Where this class of equipment is typically deployed - general reference, not this unit's own placement record.
- Operating Room
- PACU
- Emergency Department
- Labor & Delivery
- NICU
Documents & Manuals
Troubleshoot this device with Bio
Describe a symptom or error code. Bio answers from this device's own documented error codes, failure modes, parts, and guides.
Ask Bio